Manuals
/
Brands
/
Computer Equipment
/
Network Hardware
/
Honeywell
/
Computer Equipment
/
Network Hardware
Honeywell
NETAXS-123 manual
- page 8
1
8
76
76
Download
76 pages, 3.29 Mb
viii
www.honeywell.com
Contents
Main
Page
C
Installing the NetAXS-123 Panels
Page
LIST OF FIGURES
Page
LIST OF TABLES
Page
Installing the NetAXS-123 Panels
In this chapter ...
1.0 Introduction
1.1 Access Control Overview
1.2 NetAXS-123 Overview
2.0 Panel Components and Descriptions
Page
2.1 Supervised Input Wiring
Page
2.2 NetAXS-123 Access Control Unit
2.2.1 NetAXS-123 Add-On Board
2.2.2 Supported Readers
Supported readers include the following: Table 4: Readers Supported by NetAXS-123
2.2.3 Real-Time Clock Protection
2.3 Power Supply
Page
3.0 Installation
3.1 Installing the Compact Enclosure Panel
3.1.1 Installing on a Wall
Page
Page
Page
Page
3.1.3 Installing on a Flat Surface
3.2 Installing the Standard Enclosure Panel
Page
Page
Page
Page
Page
Page
Page
Page
3.3 Installing the Add-On Board
Page
Page
3.4 Wiring the Readers
Page
Page
Page
3.5 Wiring Door Strikes
OR
On-Board +12VDC Conguration
External Power Supply Conguration
Page
Page
ON ON
OFF Future Use (Default) ON Future Use
Table 8: NetAXS-123 SW1 DIP Switch Settings (continued)
Page
Page
3.6.2 Add-On Board DIP Switch and Jumper Settings
Page
3.7 Communications
3.7.1 USB Communications
Page
3.7.2 RS-485 Communications
Page
Page
Page
4.0 System Configuration
4.1 Ethernet Connection
4.2 USB Connection
4.3 RS-485 Connection via PCI-3
Page
4.5 RS-485 Connections with Multidrop Panels at Both Ends of the Cable
NetAXS-123 Access Control Unit Installation Guide, Document 800-05779, Revision A 53
Figure 17: RS-485 Connection via PCI-3 with Multidrop Panels at Both Ends
Note: You should ground each NetAXS-123 Standard (Metal) Enclosure panel individually with an
Earth Ground.
PCI3
54 www.honeywell.com
4.6 M-56K Dial-up Modem, RS-485 Connection via Hub (PCI-3)
Note: You should ground each NetAXS-123 Standard (Metal) Enclosure panel individually with an
Earth Ground.
DIP Switch Settings S1-S5 Panel Address S6: OFF S7: OFF S8-S9: OFF: 485 Termination OFF
DIP Switch Settings S1-S5 Panel Address S6: OFF S7: OFF S8-S9: ON: 485 Termination ON
Page
Page
Page
58 www.honeywell.com
4.10 NetAXS-123/NetAXS-123 Access Controller Panel Connection Detail
X
485 -
Figure 22: NetAXS-123/NetAXS-123 Access Controller Panel Connection Detail
DO NOT CONNECT or GROUND SHIELD
Ground only one side of cable shield Shield
Page
5.0 Hardware Specifications
5.1 Relay Contacts
5.2 Reader Interface
5.3 Maximum Output Loading
5.4 PoE Power Limitations
5.5 Mechanical
Page
6.0 Basic Standalone Operation
6.1 Card Read / Door Lock Operation
6.2 Door Egress / Door Lock / Door Status Operation
7.0 Maintenance
8.0 Troubleshooting
Table11 Troubleshooting Problems and Solutions
