DESCRIPTION OF THE CONTROL PANEL

F GH I

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A B

C

 

 

D

E

A

"ON/OFF" button

F

"SALT EMPTY" light

 

 

B "DELAY START" button
G "PROGRAMME STATUS" lights/

C

Open door

 

 

"DELAY START" time lights
H "PROGRAMME SELECTION" lights

D

"PROGRAMME" buttons

I

"OPTION SELECTION" light

E

"HALF LOAD" option button

 

 

 

 

 

 

 

 

 

 

DIMENSIONS:

 

 

with working top
without working top

Height

 

 

82

cm

85

Depth

cm

60

57,3

Width

cm

60

59,8

Depth with door open

cm

120

117

 

 

 

 

TECHNICAL DATA:

EN 50242 place load

15

Capacity with pans and dishes

9 persons

Water supply pressure

Min. 0,08 - Max 0,8 MPa

Fuse

(see rating plate)

Power input

(see rating plate)

Supply voltage

(see rating plate)

PROGRAMME SELECTION AND SPECIAL FUNCTIONS

(Use in conjunction with programme guide)

IMPORTANT

The dishwasher has one very practical functions:

the "recommended" programme (which is ideal for full load daily use) for quick and accurate selection.

Programme settings

■Open the door and place the dirty dishes inside the appliance.

■Press the "ON/OFF" button .

■After pressing the "ON/OFF" button, the indicator light which is factory set at

"recommended” will flash.

■If you wish to select an option, press the option button (the corresponding indicator light will light up).

The option button can be selected or deselected WITHIN 2 minutes of the programme commencing.

■Choose a programme by pressing the corresponding button.

■When the door is shut, after an audible signal has sounded, the programme will start automatically.

WITHIN 2 minutes of the programme commencing another programme can be selected, simply by pressing the corresponding button.

IMPORTANT

To select the "PRE RINSE" programme, simultaneously press the "RAPID" programme button and "HALF LOAD" option button.

Programme interruption

Opening the door when a programme is running is not recommended especially during the main wash and final hot rinse phases. However, if the door is opened while a programme is running (for example, to add dishes) the machine stops automatically.

Close the door, without pressing any buttons. The cycle will start from where it left off.

IMPORTANT

A running program can be interrupted without opening the door by pressing the "ON/OFF" button. In this case, simply press the "ON/OFF" button again to restart the cycle from where it left off.

WARNING!

If you open the door during the drying cycle, an audible audio signal advises you that the drying cycle has not yet finished.

Changing a running programme

Proceed as follows to change or cancel a running program:

■Hold down the current programme button (with the indicator light on) for at least 5 seconds. The programme indicator lights (except for the "RAPID" programme indicator light) will flash.

■The running programme will be cancelled and the indicator light for the “recommended” programme will start to flash.

■At this point a new programme can be set.

IMPORTANT

To cancel the "PRE RINSE" programme, simultaneously hold down the "RAPID" programme button and "HALF LOAD" option button.

20

21