Rinse aid and refined salt
Only use products which have been specifically designed for dishwashers. Do not use table salt or industrial salt, or washing up liquid.
Follow the instructions given on the packaging.
If using a
number 3).
- Press the P button repeatedly until the desired hardness EN level has been reached
table), up to a maximum of five levels.
-To exit the function, wait approximately 30 seconds or press another option button, or switch off the machine using the ON/OFF button.
Even if using
If you do not add salt or rinse aid, the LOW SALT* and LOW RINSE AID* indicator lights remain lit.
Measuring out the rinse aid
Rinse aid makes it easier for the crockery to dry, as water runs off surfaces more readily and therefore does not leave streaks or marks.
The rinse aid dispenser should be filled:
•When the LOW RINSE AID* indicator light on the control panel is illuminated;
Water Hardness Table
°dH |
|
| °fH | mmol/l | level | ||
0 |
| 6 | 0 | 10 | 0 | 1 | 1 |
6 |
| 11 | 11 | 20 | 1.1 | 2 | 2 |
12 |
| 17 | 21 | 30 | 2.1 | 3 | 3 |
17 |
| 34 | 31 | 60 | 3.1 | 6 | 4 |
34 |
| 50 | 61 | 90 | 6.1 | 9 | 5* |
For values between 0°f and 10°f, we do not recommend the use of salt.
*this setting may cause a slight increase in the duration of the cycle.
(°dH = hardness measured in German degrees - °f = hardness measured in French degrees - mmol/l = millimoles
H |
F |
G |
1.Open the dispenser by turning the lid (G) in an anticlockwise direction.
2.Pour in the rinse aid, making sure it does not overflow from the dispenser. If this happens, clean the spill immediately with a dry cloth.
3.Screw the lid back on.
NEVER pour the rinse aid directly into the appliance tub.
per litre)
Measuring out the refined salt
In order to achieve the best possible results using a wash cycle, make sure that the dispenser is never empty. Refined salt removes limescale from the water, thus avoiding the formation of deposits on crockery.
The salt dispenser is located in the lower part of the dishwasher (see Description) and should be filled:
• When the green float* cannot be seen by simply looking at |
the cap of the salt dispenser. |
* |
Adjusting the amount of rinse aid
If you are not completely satisfied with the drying results, you may adjust the quantity of rinse aid used. Use a screwdriver to turn the dosage adjuster (F) to one of the 6
•If there are streaks on the crockery, set the adjustment device to a lower number
•If drops of water remain on the crockery or if there are limescale marks present after the cycle has finished, set the adjuster to a higher number
Setting the water hardness
Every dishwasher is equipped with a water softener which, by using refined salt designed especially for this type of appliance, supplies water without limescale which is then used to wash the crockery.
This dishwasher offers a setting which helps to reduce pollution and optimises washing performance in accordance with the water hardness level in your area. This information can be obtained from the organisation which supplies your household with water.
-Switch on the appliance by pressing the ON/OFF button.
-Press the P button and hold for approximately 5 seconds; two short beeps will sound and the display will show “WATER HARDNESS”; the set hardness number will flash slowly on the display (the water softening system is set by default to
• When the LOW SALT indicator light on the control panel is |
illuminated; |
1. Remove the lower rack and |
unscrew the container cap |
(anticlockwise).
2. The first time you do this: fill the
water tank right up to its edge.
3. Position the funnel* (see figure) and fill the salt container right up to its edge (this should hold approximately 1 kg); it is not
unusual for a little water to leak out.
4.Remove the funnel* and wipe any salt residue away from the opening; rinse the cap under running water and then screw it on, the head facing downwards so as to let the water flow out
of the four cracks which are arranged in a star shape on the lower part of the cap. (the container cap with the green float*)
It is advisable to perform this procedure every time you add salt to the container.
Make sure the cap is screwed on tightly, so that no detergent can get into the container during the wash cycle (this could damage the water softener beyond repair).
When necessary, measure out the salt before a wash cycle so that any saline solution which has leaked out of the salt dispenser is removed.
* Only available in selected models. | 11 |
