GB

 

 

The Company shall not be held responsible for any

 

 

incidents that occur if these regulations are not observed.

 

Anti-condensation strip*

After installing the dishwasher, open the door and stick the adhesive transparent strip under the wooden shelf in order to protect it from any condensation which may form.

Technical data

Dimensions

width 60 cm

height 85 cm

 

 

 

depth 60 cm

Capacity

14 standard place-settings

Water supply

0,05 ÷ 1MPa (0.5 ÷ 10 bar)

pressure

7,25 – 145 psi

Power supply voltage

See appliance data plate

 

 

 

 

Total absorbed power

See appliance data plate

 

 

 

 

Fuse

See appliance data plate

 

 

 

This dishwasher conforms to the

 

 

 

following European Community

 

 

 

Directives:

 

 

 

-2006/95/EC (Low Voltage)

 

 

 

-2004/108/EC (Electromagnetic

 

 

 

Compatibility)

 

 

 

-2009/125/EC (Comm. Reg.

 

 

 

1016/2010) (Ecodesign)

 

 

 

-97/17/EC (Labelling)

 

 

 

-2012/19/EU Waste Electrical

 

 

 

and Electronic Equipment

 

 

 

(WEEE)

 

 

 

Connecting the water supplies

Connection to the water and electricity supplies should only be performed by a qualified technician.

The dishwasher should not stand on top of the water hoses or the electricity supply cable.

Connecting the water inlet hose

The water inlet and outlet hoses and the electricity supply cable may be positioned towards the right or the left in order to achieve the best possible installation.

To a suitable cold water connection point: before attaching the hose, run the water until it is perfectly clear so that any impurities that may be present in the water do not clog the appliance; after performing this operation, screw the inlet hose tightly onto a tap with a ¾ gas threaded connection.

To a suitable hot water connection point: your dishwasher may be provided with hot water from the mains supply (if you have a central heating system with radiators) provided that it does not exceed a temperature of 60°C.

Screw the hose to the tap as described for connection to a cold water supply.

If the inlet hose is not long enough, contact a specialist store or an authorised technician (see Assistance).

The water pressure must be within the values indicated in the Technical data table (see Installation).

The hose should not be bent or compressed.

The appliance must be connected to the water supply network using new hoses.

Do not use old hoses.

Ensure that the new hose supplied is connected and the old hose is disposed of safely.

DO NOT overtighten the hose connector, hand tight is sufficient.

Ensure the fill hose is not kinked.

Tap connections*: A range of adaptors are available to suit your tap.

DO NOT connect the dishwasher to a single outlet instantaneous water heater or an electric heater.

Sink Waste System

Connect the outlet hose (without bending it) to a drain duct with a minimum diameter of 32 mm.

The outlet hose must be at a height ranging from 40 to 80 cm (from 15’’ to 31’’) from the floor/surface where the dishwasher rests (A).

before connecting the drain hose, remove any internal restrictions; this will prevent a build up of debris which could cause a blockage

remove any restrictions from the waste spigot and ensure that the sealing bung is removed (B).

It MUST NOT be connected to a surface water drain.

Untie the end of the GREY drainage hose from the rear of the appliance.

If fitting an under sink waste disposal unit, cut out the membrane, bung or blanking plug.

*Only available in selected models.

6

Page 6
Image 6
Hotpoint fdeb 31010 manual Connecting the water supplies, Sink Waste System, Anti-condensation strip

fdeb 31010 specifications

The Hotpoint FDEB 31010 is a highly regarded model in the realm of freestanding tumble dryers, designed to deliver efficient performance and user-friendly features. One of its standout characteristics is its generous 9 kg capacity, making it an ideal choice for larger households. This ample space allows users to dry more laundry in a single cycle, which not only saves time but also energy.

One of the key technologies integrated into the FDEB 31010 is its sensor drying capability. This innovative feature automatically detects the moisture level in the clothes and adjusts the drying time accordingly. As a result, users can avoid over-drying, protecting their garments from damage while also conserving energy. The dryer offers various drying programs tailored to different fabric types, ensuring optimal care for everything from delicates to cotton.

The Hotpoint FDEB 31010 also stands out for its ease of use. It features a simple and intuitive control panel, allowing users to select their preferred drying program quickly. The delay timer function is another convenient addition, enabling users to set the machine to start at a later time, which is perfect for taking advantage of off-peak electricity rates.

Energy efficiency is a significant consideration in today’s appliances, and the FDEB 31010 addresses this by boasting a B energy rating. While not the highest rating available, it still offers a commendable balance between performance and energy consumption, translating into savings on the utility bills.

Maintenance is made simple with the dryer’s easy-to-access filter and water tank. Regular cleaning of these components not only enhances drying performance but also prolongs the life of the appliance.

In terms of design, the Hotpoint FDEB 31010 features a modern aesthetic that can seamlessly blend into various laundry room styles. Its sturdy build ensures durability, while the white finish adds a classic touch.

In summary, the Hotpoint FDEB 31010 is an excellent choice for families and individuals seeking a reliable tumble dryer. With its generous capacity, advanced drying technologies, user-friendly interface, and energy-efficient operation, it meets the demands of contemporary laundry needs, making it a valuable addition to any home.