Start and Programmes
GB
The Controls
●PROGRAMMES knob
!Warning, if after pressing the Start/Pause button 
the programme knob position has changed, the new position will NOT change the programme selected.
To change a selected programme, press the Start/Pause button 
, the light flashes Amber to indicate the programme is paused. Select the new programme and any options required, the light will then flash green. Press the Start/Pause button
again and the new programme will start.
●OPTION buttons / lights
These buttons are used to customise the selected programme to your requirements. A programme must have been selected on the programmes knob before an option can be selected. Not all options are available for all programmes (see Start and Programmes). If an option is not available and you press the button, the buzzer will beep three times. If the option is available there will be one beep and the option light next to the button lights to confirm the selection.
After the Start/Pause button has been pressed only the Pre Care and Post Care options can be changed.
Time Delay (Delay Start)
The start of some programmes (see Start and Programmes) can be delayed for up to 24 hours. Press this button, the display shows OFF and the option light comes on. Press again and a 1 hour delay is selected and the display indicates 1hr, each further press of the button adds 1hr to the delay. When 24hr is displayed a further press the display shows OFF and after a couple of seconds cancels the delay. You can also cancel the delay by pressing the On/Off button.
Pre Creasecare (Pre Care)
This option is only available if a delayed start has been selected. It tumbles the clothes occasionally during the delayed period to help prevent creases developing.
High Heat
Available for Timed Drying programmes. Press this button and a High Heat setting is selected and the light next to the button comes on.
Timed programmes have a default of low heat, if the light next to the button is on then pressing this button selects a low heat setting and the light goes out.
Post Creasecare (Post Care)
When available and selected, the clothes are occasionally tumbled after the end of the drying and cool tumble cycles, to help prevent creases developing should you not be available to remove the load immediately the programme is complete.
●DISPLAY 
The display shows either the amount of time delay remaining or an indication of the amount of time left for a drying programme.
The delay time is displayed in hours and counts down each minute.
The time to end is displayed in hours and minutes and counts down each minute, this includes the cool tumble phase. When timed programmes are selected the time displayed throughout the cycle is the actual time remaining.
When a sensing programme is selected the time displayed is an estimate of the time remaining. When the programme is selected the display shows the time required to dry a full load, after around 10 minutes the controller calculates a better estimate of the cycle time. The colons between the hours and minutes in the display flash to show that the time is counting down. When the programme finishes its cool tumble phase the display will show E88 .
The display also shows if there is a problem with your dryer, if this occurs the display will show F followed by a fault code number (see Troubleshooting).
●Door Opening
Opening the door (or pressing the Start/Pause button 
) during a programme will stop the dryer and have the following effects:
●The Start/Pause light flashes Amber.
●During a delay phase the delay will continue to count down. The Start/Pause button 
must be pressed to resume the delay programme. The progress lights will change to show current status.
●During the drying part of the programme, the time to end count continues but the colons do not flash. The Start/Pause button 
must be pressed to resume the programme. The progress lights will change to show the current status.
●During the post creasecare phase of a drying programme, the programme will finish. Pressing
the Start/Pause button 
will
●The Start/Pause button 
must be pressed to resume the programme. The progress lights will change to show the current status and the Start/Pause light will stop flashing and turn green.
●Changing the Programmes knob will select a new programme and the Start/Pause light will flash green. You can use this to select the Cool Tumble
programme 
to cool the clothes, if you find them dry enough. Press the Start/Pause button 
to begin a new programme.
●Note
If you have a power cut, switch off the power or remove the plug. When the power is restored, press the Start/Pause button 
and the programme will resume.
8
