Hotpoint tvfg 65c manual Controls Programmes knob, Option buttons / lights, Display, Door Opening

Start and Programmes

The Controls

●Programmes knob

!Warning, if after pressing the START/PAUSE button the programme knob position has changed, the new position will NOT change the programme selected.

To change a selected programme, press the

START/PAUSE button , the light flashes Amber to indicate the programme is paused. Select the new

programme and any options required, the light will then

flash green. Press the START/PAUSE button again and the new programme will start.

●OPTION buttons / lights

These buttons are used to customise the selected programme to your requirements. A programme must have been selected on the programme knob before an option can be selected. Not all options are available for all programmes (see Start and Programmes). If an option is not available and you press the button, the buzzer will beep three times. If the option is available the option light in the button lights to confirm the selection.

After the START/PAUSE button has been pressed only the Crease Care or Sound options (where available) can be changed.

Progress ( Drying, Cool Tumble) icons

These are part of the Display, they indicate the progress of the dryer. Each icon comes on as the corresponding phase starts.

Time Delay (Delay Timer)

The start of some programmes (see Start and Programmes and The Display) can be delayed for up to 24 hours.

Crease Care

The pre-care option is only available if a delayed start has been selected. It tumbles the clothes occasionally during the delayed period to help prevent creases developing.

The post-care option occasionally tumbles the clothes after the end of the drying and cool tumble cycles to prevent creases developing, should you not be available to remove the load immediately the programme is complete. The display will show ‘End’ Note: The Crease Care and the Start/Pause lights flash Amber during this phase. Selecting this option enables both the pre and post care functions if appropriate and when selected the light in the button is lit.

Note: If you have selected the Sound option this option is not available.

Heat Level buttons and lights

Not all programmes allow you to change the heat level and some programmes allow all three heat level options: Low, Medium and High.

When the heat level options are available pressing this button changes the heat level and the light corresponding to the selection is lit.

Sound

If selected, gives a signal at the end of the drying cycle, to remind you that the clothes are ready to be removed. Not available with the Heat & Enjoy programme.

Note: If you have selected the Crease Care option this option is not available.

●DISPLAY 8:88

The display shows either the amount of time delay remaining or an indication of the amount of time left for a drying programme (see The Display).

The colons between the hours and minutes in the display flash to show that the time is counting down.

When the programme finishes its cool tumble phase the display will show ‘End’.

●Door Opening

Opening the door (or pressing the Start/Pause button) during a programme will stop the dryer and have the following effects:

Note: The Start/Pause light flashes Amber during the Post Care phase of a programme.

●The START/PAUSE light flashes Amber.

●The START/PAUSE button must be pressed to resume the programme, including a delayed start. The progress lights will change to show the current status and the START/PAUSE light will stop flashing and turn green.

●During a delay phase the delay will continue to count down.

●During the post-care phase of a drying programme, the programme will finish. Pressing the START/PAUSE button will re-start a new programme at the beginning.

●Changing the programmes knob will select a new programme and the START/PAUSE light will flash

green. You can use this to select the Refresh programme to cool the clothes, if you find them dry enough. Press the START/PAUSE button to

begin a new programme.

●Note

If you have a power cut, switch off the power or remove the plug. When power is restored, press and hold the ON/OFF button until the dryer reactivates, then press the Start/Pause button.

GB

Information	Important
Installation
Description
The Display
Programmes	Start and
Laundry
Suggestions	Warnings and
and Care	Maintenance
Troubleshooting
Service

11