Hotpoint WD440, WD640, WD420 Something Wrong? Troubleshooting, Problem, Possible causes / Solution

Models: WD645 WD440 WD640 WD420

1 24
Download 24 pages 44.01 Kb
Page 21
Image 21

Something Wrong? - Troubleshooting

If your machine seems not to be working, GO through the following troubleshooting suggestions BEFORE you call your Service Centre (see Service).

Section 1: All Aquarius Models - General Troubleshooting

GB

Problem:

The machine won’t start: (Nothing lights up on the control panel).

Possible causes / Solution:

Check the appliance is fully plugged into the socket and switched on.

Is the socket ok? Try another appliance in the socket to check.

Is the fuse in the plug ok? If not, replace it, fuse must be 13 Amps (see Care and Maintenance).

There has been a power failure - Check another electrical device in your home to see if this is the case.

The ON/OFF button has not been pressed.

The Start/Cancel button has not been pressed, for at least 3 seconds - Press and hold the Start/Cancel button until the machine starts to operate.

Description

Contents

Lights illuminate on the control panel but the wash cycle will not start.

The machine fails to fill with water.

The machine does not drain or spin (during the first wash cycle, after installation).

The appliance door is not shut properly - Close the door firmly and try the machine again.

The Start/Cancel button has not been pressed, for at least 3 seconds - Press and hold the Start/Cancel button until the machine starts to operate.

The cold water supply tap is not turned on

-Aquarius only: ‘Wash’ indicator light is flashing on the control panel.

-Aquarius+ only: ‘H20’ is shown in the display.

Aquarius+ only: Have you selected Time Delay (see Programmes and Option Modifiers).

The Start/Cancel button has not been pressed, for at least 3 seconds - Press and hold the Start/Cancel button until the machine starts to operate.

The machine has failed to take in water (see Installation)

-Is the ‘Wash’ indicator light flashing (Aquarius only)?

-Is ‘H20’ shown in the display (Aquarius+ only)?

Check that:

-Both of the cold water inlet hoses are connected to the cold water supply tap, using the ‘Y’ piece connector.

-The hoses are not kinked.

-The cold water supply tap is turned on... Ensure that it is turned fully on.

-The water pressure is sufficient (see Technical Details Chart).

-The inlet filters are not blocked... Turn off the water, unscrew both fill hoses at the back of the appliance, then remove and clean the filters.

Note: Modern machines use less water and the water taken into the machine is automatically adjusted depending on the load in the drum. For this reason, you may not always be able to see water in the drum: But if the load is ‘wet’ and the machine completes the wash cycle then the amount of water into the machine is sufficient.

Has the drain hose been installed correctly (see Installation).

Are the drain hose, standpipe or undersink connections blocked?

Note: If the drain hose is connected to an undersink ‘U’ trap - Check that the sink trap blanking plug was removed before the drain hose was connected. This is the most common installation fault.

Is the drain hose kinked or squashed - Check the hose at the back of the machine.

Carry out the additional checks listed below...

Explained

WashLabels

Installation

 

Features

ControlPanel

Modifiers

and Programmes Option

andLaundry

Detergents

Maintenance

Careand

The machine does not drain or spin (although it has drained/spun during previous wash cycles).

The programme takes a long time.

There has been an unbalanced load in the drum and the machine could not spin - Try the machine again with a different wash load (see ‘ Automatic Features’, Programmes and Option modifiers).

Has the ‘Rinse Hold’ option been selected? ‘Rinse Hold’ indicator light will flash.

-To complete the paused programme press either the Start/Cancel button or the Rinse Hold button (see Programmes and Option modifiers).

If the machine completes the wash cycle, it is unlikely there is a problem.

Check the programme table to be sure the programme you have selected is that most suited for your needs - The table also gives an indication of approximate programme times you can expect.

Note: The programme times listed in the Programme Table are approximate. Options selected can affect the programme times (see Programmes and Option Modifiers). The wash load, temperature and pressure of the incoming water supply can cause some variation in the programme times.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

andAdvice

Precautions

Troubleshooting

Wrong Something -

Service

 

 

 

21

Page 21
Image 21
Hotpoint WD440, WD640, WD420, WD645 manual Something Wrong? Troubleshooting, Problem, Possible causes / Solution

WD645, WD440, WD640, WD420 specifications

The Hotpoint WD420, WD640, WD440, and WD645 are an impressive range of washer-dryers designed to meet the diverse needs of modern households. Each model is characterized by its combination of efficient washing and drying capabilities, making them ideal for those who value convenience without sacrificing performance.

The Hotpoint WD420, known for its compact design, is perfect for smaller living spaces. It boasts a 6 kg washing capacity and a 5 kg drying capacity, making it sufficient for individuals or small families. Its 1200 rpm spin speed ensures efficient water extraction, reducing drying time significantly. This model features the ‘Anti-Ageing’ program, which uses lower temperature washes and spins to help protect delicate fabrics, prolonging their lifespan.

In contrast, the WD640 offers a more extensive capacity, with a 7 kg washing and a 5 kg drying capability. This model introduces advanced features such as the ‘Rapid Wash’ program, which allows users to wash small loads in just 30 minutes - ideal for those busy days when time is of the essence. It also includes a sensor drying function, which adjusts the drying time based on the moisture levels in the drum, ensuring energy efficiency and protecting clothes from overdrying.

The WD440 enhances the drying experience with its 6 kg washing and 5 kg drying capacities. A notable characteristic of this model is its ‘Cotton’ cycle, designed specifically to handle cotton fabrics like shirts and bed linens, providing optimal cleaning and drying. Additionally, the model includes a delay timer, allowing users to set the appliance to start at their convenience, a great feature for balancing busy schedules.

Finally, the WD645 epitomizes versatility, featuring a larger washing capacity of 8 kg and a drying capacity of 6 kg. It comes equipped with Smart Technology, which utilizes sensors to monitor load size and optimize wash cycles for the best performance. The model also features a special ‘Wool’ cycle, ensuring that woolen items are washed gently, thus preventing any shrinkage or damage.

Together, these Hotpoint washer-dryer models combine innovative technologies with user-friendly features such as various wash programs, energy efficiency, and compact designs. They truly cater to the needs of contemporary life, making laundry tasks simpler and more efficient, benefiting households of all sizes and lifestyles.