STEP 2 | Installation |
|
|
TECHNICAL DETAILS
1
REMOVE TWO TRANSIT FIXINGS... Follow these instructions to remove the TWO transit fixings.
2CONNECT TO THE WATER
| WF445,WF440,WF430,WF250, |
Models | WF240,WF225,WF220, WF215, |
| WF210 and WF000 |
IMPORTANT: Situated, one either side of the rear panel, both transit bolts
It is important the transit bolt and spacer come out intact (see pic).
SUPPLY...
PLEASE USE THE NEW HOSES SUPPLIED, FITTED TO THE MACHINE.
| 59.5cm wide |
Dimensions | 85cm high |
| 60cm deep |
|
|
Capacity | from 1 to 6kg |
(complete with spacers) MUST be removed before use...
Failure to do so may cause damage to your machine!
Use a crosshead
screwdriver to
remove the
plastic cover.
Unscrew the bolt using a 13mm spanner.
STOP when 3
threads can be
seen.
Hold, slide
across and pull
to remove.
For safety, replace both plastic covers over the holes left by removing the two bolts.
DO NOT REMOVE!
i | Check both hot | ii |
and cold water |
Old hoses may cause leaks due to worn out washers or may split due to water pressure.
Connect fill hoses to the water supply taps:
Electric | voltage 220/230 Volts 50Hz |
Connections | maximum absorbed power 1700W |
3 DRAINAGE SYSTEM... we recommend one of the following:
supplies are |
running freely... |
Red or Grey Hose end to Hot and Blue Hose end to Cold.
TURN BOTH TAPS ON...
Spin Speed | up to 1500rpm - WF250 |
| up to 1400rpm - WF445,WF440 |
| & WF240 |
| up to 1300rpm - WF430 |
| up to 1200rpm - WF225 & WF220 |
| up to 1100rpm - WF215 & WF210 |
| up to 1000rpm - WF000 |
Control |
|
programmes | programme D |
according to | temperature 60˚C |
IEC456 | run with a 6kg load |
directive |
|
NOTE: ALTHOUGH YOU MAY NEED TO MOVE THE HOOKED END SUPPORT ALONG THE GREY DRAINAGE HOSE, DO NOT REMOVE IT.
WHICHEVER DRAINAGE METHOD YOU USE, MAKE SURE THAT THE HOOKED END SUPPORT IS FIXED LEVEL TO, OR ABOVE THE ‘PLUMBING INDICATOR LINE’*
(*see Getting to Know your Appliance)
STANDPIPE METHOD
Hooked End Support
Insert drainage hose approximately 100mm into the standpipe.
.............................
Standpipe height: minimum 500mm from the floor.
OR
UNDER SINK METHOD
cut off the blocked end of the under sink drainage unit.
800mm from floor
Fix the hooked | Attach the GREY |
end support at | drainage hose to the |
a minimum | under sink drainage |
800mm from | unit securely, using a |
the floor. | hose clip. |
iii | Check the hoses | iv Water pressure at the tap | |
|
| at least once a | must be in the range... |
|
| year. Replace any | Max. 1Mpa (10 bar) and |
|
| that show signs of | Min. 0.05Mpa (0.5 bar) |
|
| cracking, they |
|
|
| might burst due |
|
|
| to water pressure. |
|
|
|
|
|
If you have no hot water supply...
A cold fill adaptor is available from your local Hotpoint authorised Service Centre or by calling the Genuine Parts & Accessories Hotline (see KEY CONTACTS).
4
LEVEL?...
YOUR MACHINE WILL BE NOISY IF THE TWO FRONT FEET ARE NOT ADJUSTED SO THE MACHINE STANDS FIRM AND LEVEL.
The inclination of the machine, measured on the top, must not exceed 2˚.
-Move your machine into final location. Take care not to trap or kink the hoses.
-Turn one or both front feet clockwise until the machine stands firm and level.
The spring on each foot will stop them coming loose.
If it is placed on a fitted carpet, adjust the feet to ensure that there is adequate ventilation beneath the washing machine.
5
CONNECT TO THE POWER SUPPLY...
PLUG YOUR MACHINE INTO AN ELECTRICAL SOCKET WHICH IS EASILY ACCESSIBLE. SWITCH ON
NOTE: Hotpoint recommend extension
leads are not used.
NOTE: The mains cable must only be replaced by an authorised serviceman.
6
READY...
TO CHECK ALL PARTS OF THE INSTALLATION AND TO THOROUGHLY CLEAN THE INSIDE OF YOUR MACHINE:
RUN PROGRAMME ‘B’ (refer to ‘Programme Selection’, STEP 4).
✗ | WITHOUT ANY LAUNDRY |
|
|
| |
and | ✗ | |
| WITHOUT ANY DETERGENT | |
|
|
THIS WILL TAKE APPROXIMATELY 2hours 30minutes TO COMPLETE
