HP AE40L LIFT AND TRAIL HITCH, AERA-vator

LIFT AND TRAIL HITCH

ITEM NO.	ORDER NO.	DESCRIPTION	ITEM NO.	ORDER NO.	DESCRIPTION

1	AE80-099	"A" FRAME - 40L	20	HW30012TAZP	3/8" FLAT WASHER
2	AE80-090	SWING MAST - 40L	21	HW24012GBZPC	3/8" STOVER LOCKNUT
3	AE80-087	SWING STAND - 40L	22	HW40004032ZP	1/8" X 1" COTTER
4	AE80-093	CLEVIS - 40L	23	AE50-063	AERA-vator DECAL
5	AE80-006	SWING LOCK - 60	24	HW01012040G5ZPC	3/8" X 1-1/4" HEX CAP G5
6	AE80-089	SWIVEL PIN - 40L	25	AE50-059	SMALL F.P. DECAL
7	AE50-134	9/16"X4X.047SPRING(NotShown)	26	HW01012032G5ZPC	3/8" X 1" HEX CAP G5
8	AE80-096	SWING LOCK LINK - 40L	27	HW22012G5ZPC	3/8" FLANGE LOCK NUT
9	AE80-011	LOCK HINGE PIN - 60	28	HW25020G5ZPC	5/8" JAM NUT
10	AE80-017	LOCK SETSCREW - 60	29	HW32024G5ZP	3/4" LOCK WASHER
11	HW25024G5ZPC	3/4" HEX JAM NUT	30	HW31012TAZP	3/8" FLATWASHER SAE
12	AE50-069	1/4" HIGH TEST CHAIN X 9 LINKS	31	AE50-040	3/8" X 1-1/2" PIN
13	AE50-022	LOCK SPRING	32	HW20028G5ZPF	7/8" NF HEX NUT
14	AE50-023	LIFT ARM PIN	33	AE50-075	CAUTION(PINCHPOINT)
15	AE50-120	3/4" X 1" FLANGE BEARING	34	AE50-163	P.B. CYLINDER CLAMP
16	HW33028G8ZP	7/8" HVY. L'WASHER	35	AE50-164	P.B. CYLINDER
17	AE26-036	MAST HINGE ROD - 40L	36	HW01008024G2ZPC	1/4" x 3/4" HEX CAPSCREW
18	HW31028TAZP	7/8 SAE FLAT WASHER	37	HW22008G5ZPC	1/4" FLANGE LOCKNUT
19	HW40006040ZP	3/16" X 1-1/4" COTTER	38	HW20008G5ZPC	1/4" HEX NUT

	24
	21							20
	21	29	11
		29	11					21
	20				7	12		21
	20				7	12
				22				26
		15		30					27
									26		35
										28	35	34
		8								28		34	36 38 37
													36 38 37
13
21
20					5								23
20			CAUTION		5								4
		33
2			FRAME PINCH POINT						AERA-vator
2			HAZARD - KEEP AWAY						AERA-vator
					10
	19 17			9
			IRST		22	16 16	18	32		15
			RODUCTS INC.				18	32
			TIFTON, GA. 31794
			25										11
													11
	6								31		6	29
												29

14

1

3

20

Contents

FIRST PRODUCTS INC 164 Oakridge Church Rd Tifton, Georgia 31794 U.S.A Phone (229) Fax (229) INTRODUCTION REMEMBER SAFETY IS ALWAYS FIRST ATTENTION: TABLE OF CONTENTS UNDERSTANDING HOW THE SWING HITCH OPERATES (PRIOR TO HITCHING TO TRACTOR) Reassembly and Installation Page WARNING SAFETY DECALS OPERATION SAFETY Your Safety Is Always First All operators should prior to adjusting, maintaining, hitching to, or operating the AERA-vator: OPERATION SAFETY For the safety and instruction of all operators, keep this manual stored on the •Instruct all people in the work area to stay clear of the unit •Perform all pre-operationchecks (page 8) prior to start up OPERATOR INSTRUCTIONS UNDERSTANDING HOW THE SWING HITCH OPERATES (PRIOR TO HITCHING TO TRACTOR) CORRECTLY ADJUSTING THE HITCH TO THE TRACTOR OR APPLY DOWN PRESSURE TO THE TRACTOR LIFT LINKS DURING OPERATION Do not back the unit up with the PRE-OPERATIONCHECK LIST •Pin the swing stand in the up position MAINTENANCE SAFETY OPERATOR MAINTENANCE CHECK BELT TENSION AE40L SERVICE INSTRUCTIONS ROTOR SHAFT I.Removal & Disassembly (Clean the machine thoroughly with a pressure washer) Removal & Disassembly A. Removal of Rotor Shaft Assembly from Main Frame C. Rotor Disassembly 2. Remove the internal snap rings on both sides 3. With the Rotor sitting on the press table press out the bearing assembly II.Reassembly and Installation A. Rotor Hub Re-Assembly B.Assembly of Rotor Shaft bores aligned To assist with aligning timing marks between rotors, use chalk or marker to mark two rotor shaft flats degrees apart next to the threaded end. The selected TINE REPLACEMENT SEEDER MAINTENANCE Re-assemble SEEDER CALIBRATION CALIBRATION I. GENERAL OBSERVATIONS II. CALIBRATION PROCEDURE WARRANTY INFORMATION ONE YEAR LIMITED WARRANTY MAIN FRAME ASSEMBLY DRIVE TRAIN COMPONENTS LIFT AND TRAIL HITCH ROTOR ASSEMBLY DRIVE LINE COMPONENTS SMOOTHING ROLLER GROOMING RAKE & BRUSH 40L SEEDER MOUNTING 42" SEEDER DRIVE 42"SEEDER PARTS LIST FP#: DO50-011 GANDY #: 2842FP Page Page SPECIFICATIONS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE