HP AE40L GROOMING RAKE & BRUSH

GROOMING RAKE & BRUSH

ORDER NO. AE82-030

ITEM NO. ORDER NO.

DESCRIPTION

ITEM NO. ORDER NO.

DESCRIPTION

1	AE50-159	Brush	11	HW03012040G5ZPC	3/8x11/4CarriageBoltG5
2	AE80-131	Groom Rake/Brush Frame	12	AE80-134	Groom Rake/Brush Arm
3	AE23-205	Washer	13	AE50-160	2 1/4" "S" Hook
4	AE50-178	Rake Tine	14	HW24016GBZPC	1/2 Stover Lock Nut
5	AE50-192	HangerChain-40	15	HW03016056G5ZPC	1/2"x13/4"CarriageBolt
6	AE80-133	Groom Rake/Brush Mount	16	HW40004032ZP	1/8 x 1 Cotter Pin
7	HW03010064G2ZPC	5/16"x2"CarriageBolt	17	HW01010024G5ZPC	5/16X3/4HexCapscrew
8	HW22010G5ZPC	5/16"HexFlangeLockNut	18	AE80-146	AE40L Grm Rake/Brush Chain Catch - LT
9	AE80-130	Tine Rod - 40	19	AE80-147	AE40L Grm Rake/Brush Chain Catch - RT
10	HW31016TAZP	1/2" Flat Washer Sae

1917

13 8

Contents

FIRST PRODUCTS INC 164 Oakridge Church Rd Tifton, Georgia 31794 U.S.A Phone (229) Fax (229) INTRODUCTION REMEMBER SAFETY IS ALWAYS FIRST ATTENTION: TABLE OF CONTENTS UNDERSTANDING HOW THE SWING HITCH OPERATES (PRIOR TO HITCHING TO TRACTOR) Reassembly and Installation Page WARNING SAFETY DECALS OPERATION SAFETY Your Safety Is Always First All operators should prior to adjusting, maintaining, hitching to, or operating the AERA-vator: OPERATION SAFETY For the safety and instruction of all operators, keep this manual stored on the •Instruct all people in the work area to stay clear of the unit •Perform all pre-operationchecks (page 8) prior to start up OPERATOR INSTRUCTIONS UNDERSTANDING HOW THE SWING HITCH OPERATES (PRIOR TO HITCHING TO TRACTOR) CORRECTLY ADJUSTING THE HITCH TO THE TRACTOR OR APPLY DOWN PRESSURE TO THE TRACTOR LIFT LINKS DURING OPERATION Do not back the unit up with the PRE-OPERATIONCHECK LIST •Pin the swing stand in the up position MAINTENANCE SAFETY OPERATOR MAINTENANCE CHECK BELT TENSION AE40L SERVICE INSTRUCTIONS ROTOR SHAFT I.Removal & Disassembly (Clean the machine thoroughly with a pressure washer) Removal & Disassembly A. Removal of Rotor Shaft Assembly from Main Frame C. Rotor Disassembly 2. Remove the internal snap rings on both sides 3. With the Rotor sitting on the press table press out the bearing assembly II.Reassembly and Installation A. Rotor Hub Re-Assembly B.Assembly of Rotor Shaft bores aligned To assist with aligning timing marks between rotors, use chalk or marker to mark two rotor shaft flats degrees apart next to the threaded end. The selected TINE REPLACEMENT SEEDER MAINTENANCE Re-assemble SEEDER CALIBRATION CALIBRATION I. GENERAL OBSERVATIONS II. CALIBRATION PROCEDURE WARRANTY INFORMATION ONE YEAR LIMITED WARRANTY MAIN FRAME ASSEMBLY DRIVE TRAIN COMPONENTS LIFT AND TRAIL HITCH ROTOR ASSEMBLY DRIVE LINE COMPONENTS SMOOTHING ROLLER GROOMING RAKE & BRUSH 40L SEEDER MOUNTING 42" SEEDER DRIVE 42"SEEDER PARTS LIST FP#: DO50-011 GANDY #: 2842FP Page Page SPECIFICATIONS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE