FP USER INSTRUCTIONS ENGLISH 71576286 - 07/06
Example of straight | Example of bevel cut |
Ensure a tightening on the stuffing box housing and not on the sleeve.
SETTING OF PACKING
Follow the instructions:
a)Assemble of the packing in S.
b)Stagger by about 90° between two rings.
c)Assemble packing after packing.
After setting the last packing ring, secure the packing with the gland and tighten the nut by hand. After tightening, the shaft should turn by hand as easily as before the setting of the packing.
| PUMP |
|
| DIMENSIONS IN MILLIMETERS |
| PACKING | ||||||
|
|
|
|
|
|
|
|
|
|
|
| |
| TYPE |
|
| D1 | D2 | D3 | D4 | D5 | L1 |
| Lgth | |
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
| ||
| 50 FP | 24 | 30 | 46 | 70 | M10 | 48 | 600 | 8 | |||
|
|
|
|
|
|
|
|
|
| |||
| 65 FP | 24 | 30 | 46 | 70 | M10 | 48 | 600 | 8 | |||
|
|
|
|
|
|
|
|
|
| |||
| 80 FP | 32 | 40 | 60 | 86 | M12 | 63 | 800 | 10 | |||
|
|
|
|
|
|
|
|
|
| |||
| 100 FP | 32 | 40 | 60 | 86 | M12 | 63 | 800 | 10 | |||
|
|
|
|
|
|
|
|
|
| |||
| 122 FP | 45 | 55 | 75 | 100 | M12 | 45 | 850 | 10 | |||
|
|
|
|
|
|
|
|
|
| |||
| 125 FP | 40 | 50 | 70 | 96 | M12 | 60 | 1000 | 10 | |||
|
|
|
|
|
|
|
|
|
| |||
| 152 FP | 55 | 70 | 95 | 135 | M12 | 78 | 1100 | 12 | |||
|
|
|
|
|
|
|
|
|
| |||
| 202 FP | 65 | 80 | 109 | 150 | M16 | 91 | 1200 | 14 | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
For arrangement of packing, see section 8.1, Sectional drawings.
6.2.6 Internal coating
If the pump has an internal coating, this coating must be inspected periodically. Any wear or cracks of the coating found must be immediately repaired. Failure to do this may lead to accelerated wear of the coating during operation and corrosion of the exposed base metal, depending on the material and pumped liquid. Special attention must be paid to the coating edges. Any loss of coating material is considered to be normal wear and tear on the pump and is not considered as warranty. Flowserve has applied the coatings according to the supplier's instructions but will not be held responsible for coating wear or cracks that may develop over time.
6.3 Spare parts
6.3.1 Ordering of spares
Flowserve keeps records of all pumps that have been supplied. When ordering spares the following information should be quoted:
1)Pump serial number.
2)Pump size.
3)Part name
4)Part number
5)Number of parts required.
The pump size and serial number are shown on the pump nameplate.
To ensure continued satisfactory operation, replacement parts to the original design specification should be obtained from Flowserve. Any change to the original design specification (modification or use of a
Page 24 of 35