Manuals / HP / Computer Equipment / Printer

HP Scitex FB700 Industrial manual Printing tips, Visible

Models: Scitex FB700 Industrial

1 102
Download 102 pages 41.83 Kb
Page 32
Image 32

Printing tips

CAUTION: Synthetic media commonly used for inkjet printing can build up a static charge, especially in environments with low relative humidity. This charge can pose an electrostatic discharge (ESD) hazard to persons, the printer, and other equipment. It can be safely discharged by draping a grounded chain or tinsel over the top of the media, or by wiping the media with a solution of 90% isopropyl alcohol and allowing it to dry for five minutes before printing. A relative humidity of 40%-60% will greatly reduce problems with static electricity.

●Rigid cut-sheet media — use only flat, unwarped, undamaged sheets, with parallel opposite edges and 90° corners. For optimal image quality, use smooth-surfaced media. Images printed on porous media will lack fine detail.

●Curing continues for 24-48 hours — the UV ink will continue to cure for a day or two after printing. Maximum durability and adhesion is achieved when the ink is fully cured.

●If you print on the media drive belt, clean the ink off the belt as soon as possible. The longer that ink remains on the belt, the more difficult it is to remove. To remove ink from the belt, moisten the ink with isopropyl alcohol, let stand for a few minutes, and wipe with a paper towel. Carefully remove any flaked ink from the area.

●To avoid printing on the media drive belt when printing edge-to-edge (0 margin) jobs, you can affix dark-colored masking tape on the belt where the sides of the media will be. Remove or replace the tape periodically as ink accumulates on the tape.

●Do not attempt to adjust the vacuum level for the printheads. It has been factory adjusted for best performance.

●Lighter, smaller media rolls — for lighter, smaller rolls of media, you can use the rigid media tables and media rollers to feed the media like rigid media.

●Printing on reflective media will reflect UV light onto the printheads, which will cure the ink over time and clog the ink jets. To minimize this:

◦Do not keep reflective media loaded on the printer when not in use.

◦Perform a manual purge after printing on reflective media.

◦Visually inspect the printheads via the service door for ink buildup or ink curing, If observed, clean the printheads (see Clean the print head orifice plates (bi-weekly) on page 70).

●To load reflective media, the General Media Setting “Visible to Printer” should be set to

Visible.

●The margins for print jobs sent from the Onyx RIP cannot be set from the RIP. The margins can be adjusted once the print job is stored on the printer, or white space can be added to the document before it is sent to the RIP.

●To reduce printing artifacts when printing on Corrugated Plastic (Coroplast) or Polystyrene (Sintra) sheets, try creating a custom media type with the lamps set to Low, Low. Note that this setting could reduce the gloss of the print.

26 Chapter 4 Printing jobs

ENWW

Page 31 Page 33
Page 32
Image 32
HP Scitex FB700 Industrial manual Printing tips, Visible
Page 31 Page 33

Scitex FB700 Industrial specifications

The HP Scitex FB700 is an industrial flatbed printer designed to meet the rigorous demands of high-quality large-format printing. Launched by HP, this printer offers businesses incredible versatility, speed, and precision, making it an essential tool for print service providers looking to enhance their productivity and expand their service offerings.

One of the standout features of the HP Scitex FB700 is its print quality. Equipped with HP's proprietary UV inks, the printer delivers vibrant colors, sharp images, and excellent durability. These inks are designed for a wide range of substrates, making it possible to print on materials such as rigid boards, flexible media, and even specialty applications like textiles. The FB700 supports a maximum print resolution of 1200 dpi, ensuring that every detail is faithfully rendered.

A key technology in the FB700 is its UV curing capability. This technology allows the printer to cure the inks almost instantly as they are applied, which not only speeds up the printing process but also enables printing on heat-sensitive materials. The ability to quickly switch between different substrates, from foam board to acrylic, offers unparalleled flexibility for businesses looking to meet diverse client needs.

Moreover, the HP Scitex FB700 features a user-friendly interface, enhanced by HP’s smart technology. This includes automated calibration and quality control systems that help maintain consistent print quality while reducing the likelihood of errors. The printer is also designed with ease of maintenance in mind, allowing operators to focus on production rather than troubleshooting.

In terms of productivity, the FB700 excels with a high throughput rate. Capable of producing prints up to 95 m² per hour, this printer is suited for high-volume jobs, enabling businesses to take on larger projects without sacrificing quality. Its robust design ensures reliability and efficiency, making it ideal for busy print environments.

Lastly, sustainability is an important consideration within the printing industry, and the HP Scitex FB700 addresses this concern by utilizing low-VOC inks and energy-efficient components. This commitment to eco-friendliness allows companies to meet their sustainability goals while maintaining a competitive edge in the market.

In summary, the HP Scitex FB700 Industrial printer is a powerful tool that combines high performance, versatility, and ease of use. With its advanced printing technologies, exceptional print quality, and commitment to sustainability, it is well-equipped to handle the diverse demands of modern printing applications.