SPOOL | PAWL |
| SPRING HUB | |
|
| |||
SHAFT |
|
| (Spring not | |
|
|
| shown) | |
| SPRING |
| SHAFT | |
SIDE VIEW | Install | END VIEW | ||
GROOVE | ||||
against flat | ||||
|
|
☞4. Unwrap hose without allowing spool to turn.
☞5. Disconnect hose from elbows inside spool wrapper.
☞6. Install new hose following directions below.
HOSE INSTALLATION
Use the following procedure to replace hose or if reel was ordered without hose. Refer to HOSE INSTALLATION REFERENCE DRAWING, below.
☞1. Unspool new hose from shipping spool and lay out to
eliminate twist.
NOTE: This step is not essential, but will aid in winding operation of the reel and prolong hose life.
☞ 12. | Replace inspection cover. | ☞ 2. | Insert hose end through guide and connect to elbows |
|
|
| inside spool wrapper. (See drawing below.) |
| HOSE REMOVAL | ☞ 5. | Wind the hose onto the reel spool by hand rotating |
Use the following procedure to remove worn or damaged hose |
| spool in direction it turns free of spring tension. | |
| (Normally clockwise when viewed from spring side) | ||
from reel prior to installation of new hose. |
| ||
☞ 6. |
| ||
1. | Move machine serviced by reel to a position closest to | Adjust hose stop (not used on machine pull reel). | |
☞ 2. | reel. Spring will still be under | ☞ 7. | Complete working end connections. |
Turn off supply pressure to reel. | ☞ 8. | Pretension reel and complete installation as | |
☞ | Disconnect hose from machine or other attachments. |
| described in REEL INSTALLATION section. |
3. |
|
| |
Remove hose stop, if installed, and allow hose to retract onto spool. Ensure all tension is off spring by manually rotating spool (normally clockwise when viewed from spring side).
HOSE INSTALLATION REFERENCE DRAWING |
|
| |||
OPTIONAL | STANDARD SPOOL |
|
| STANDARD SPOOL | |
|
| ROTATION DIRECTION | |||
VERTICAL | ROTATION DIRECTION |
|
| ||
HORIZONTAL HOSE | TO WIND HOSE WHEN | ||||
HOSE GUIDE | TO WIND HOSE WHEN | ||||
GUIDE POSITION | VIEWED FROM | ||||
LOCATION– | VIEWED FROM | ||||
(STANDARD) | SPRING SIDE | ||||
REEL | FITTING SIDE | ||||
|
|
| |||
MOUNTED |
|
|
|
| |
BASE UP |
|
|
|
| |
|
|
|
| SPRING | |
|
|
|
| MOTOR | |
ELBOW– |
| SPOOL | SPOOL | SPOOL | |
CONNECT |
| DISK | DISK | ||
SPOOLED |
|
|
| WRAPPER | |
HOSE HERE |
| HOSE ON |
| SECTIONS | |
|
| SPOOL |
|
| |
ADJUSTABLE |
| SWIVEL |
|
| |
HOSE STOP |
| FITTING |
|
| |
|
| ATTACH SUPPLY LINE HERE |
| ||
|
| NOTE: SUPPLY MUST BE |
| ||
|
| FLEXIBLE LINE. DO NOT |
| ||
|
| HARD PLUMB. |
| ||
OPTIONAL | HOSE STOP |
|
|
| |
HORIZONTAL | MOUNTING |
|
| ||
HOSE GUIDE |
| BASE |
|
| |
LOCATION | VIEW FROM FITTING SIDE |
|
| VIEW FROM SPRING SIDE | |
HUBBELL
® | GLEASON REEL CORP. | |
P.O. Box 26 • 600 South Clark St. | ||
| ||
| Mayville, WI | |
® | Phone | |
A Hubbell Company | ||
|
Printed in USA | Bulletin No. 042871.b |
