Hunter Fan Outdoor Ceiling Fan Fan Assembly Installer’s Choice Hanging System, Low Profile Fan

SUPPORTING

STRUCTURE

NEOPRENE

COVER

CEILING

PLATE

MOUNTING	RUBBER
	SPACERS
SCREWS	(OPTIONAL)

FIGURE 4

CAUTION: Use spacers only if fan is mounted to a flat ceiling.

Step 5: Fan Assembly

NOTE: Assembly Methods For

Installer’s Choice Hanging System

Your new Hunter fan can be hung in (2) different manners, one as a low profile fan, the other as a ball type hanging fan. Read Steps 5 and 7 to decide which style of mounting you prefer.

Low Profile Fan

A. The canopy has (4) holes in the bottom. The large center hole fits over the adaptor on top of the fan. The (3) remaining holes are for the canopy assembly screws.

Place the canopy on top of the fan and align the proper holes.

See Figure 5. Make certain you have located the hole pattern by checking to see that the canopy sits flat on top of the fan without a space between the bottom of the canopy and the top of the fan. If a space is present, rotate the canopy slightly, eliminating the space.

CEILING PLATE

HOOK

CEILING

PLATE

GROUND

WIRE

CANOPY

FIGURE 5A

Hanging Fan

CAUTION: Do not lift motor by wires.

A. Insert pipe nipple through canopy and feed wires from top of motor through pipe nipple. Screw pipe nipple into fan until tight (at least 4-1/2 turns). The setscrew locking the pipe nipple to motor must be tightened very securely. See Figure 5B. Failure to tighten screw could result in fan falling.

LEAD WIRES

6" MIN.

PIPE NIPPLE BALL

CANOPY

PIPE NIPPLE

MOTOR	PIPE NIPPLE
	SETSCREW
	(TIGHTEN SECURELY)

FIGURE 5B

ADAPTOR

SCREWS WITH LOCKWASHERS AND LOCTITE ON THREAD

CANOPY

SCREW HEAD

B. Being careful not to scratch the canopy finish, hang the fan from the hook in the ceiling plate using one of the (2) slots in the canopy. See Figure 5A.

Step 6: Final Wiring

A. Connect electrical supply leads to the leads from motor, using approved connectors. Connect black electrical supply lead to the black motor lead and the black with white stripe motor lead (see Note). Connect the white electrical supply lead to the

FAN ASSEMBLY

SCREW HOLE

white motor lead. Connect the ground wire to the green leads from the motor and ceiling plate.

FIGURE 5

B. Next, poke through the neoprene material behind the holes with a sharp object, then secure the canopy to the top of the fan using (3) #10-32 screws with lockwashers packaged with the adaptor kit. Make certain the screws are tight. Failure to do so could result in the fan falling.

CAUTION: To ensure proper engagement of the canopy assem- bly screws, the canopy must fit snug against the top of the fan.

CAUTION: Do not lift motor by wires.

C. Being careful not to scratch the canopy finish, hang the fan from the hook in the ceiling plate using one of the (2) slots in the canopy. See Figure 5A.

NOTE: If a separate wall switch will be used to control a light- ing accessory, connect the black wire with white stripe to the wall switch lead. The wall switch must be a listed general-use switch.

CAUTION: No bare wire or wire strands should be visible after making connections.

If a light kit is used it must be marked “Suitable for outdoor use.”

B. After making the wire connections, the wires should be spread apart with the white and green wires on one side of the outlet box, and the black and black/white wires on the other side of the box.

The splices should be turned upward and pushed carefully up into the outlet box.

C. Install the light kit in accordance with the instructions sup- plied with it.

FORM NO. 41110-01 6/95 - 2 - ©1995 HUNTER FAN CO. TM