Before Starting the Engine, Scraper BAR

OPERATION

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

•If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the hex nuts, then mov- ing skid plate to desired position. Be sure both plates are adjusted evenly. Tighten securely.

HIGH POSITION	HEX
(LOW GROUND	HEX
CLEARANCE)	NUTS
	AUGER
	HOUSING
LOW POSITION	SCRAPER
(HIGH GROUND	BAR
CLEARANCE)	SKID PLATE
	SKID PLATE

FIG. 18

SCRAPER BAR

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

TO USE DRIFT CUTTERS (See Fig. 19)

Use the drift cutters to cut through deep snowdrifts that are higher than the front of the snow thrower.

•Loosen adjustment nuts enough to allow drift cutter to be raised to highest position and tighten nuts securely. Repeat for opposite side of snow thrower.

•When not using drift cutters, loosen adjustment nuts, lower to storage position and tighten nuts securely.

AUGER

HOUSING

STORAGE	DRIFT
POSITION	CUTTER

ADJUST-

MENT NUTS

FIG. 19

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 20)

The engine on your snow thrower has been shipped, from the factory, already filled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE (See Fig. 20)

•Fill fuel tank to bottom of tank filler neck. Do not over- fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

CAUTION: Alcohol blended fuels (called gaso- hol or using ethanol or methanol) can attract moisture which leads to separation and forma- tion of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

CHOKE	ENGINE OIL	GASOLINE
CONTROL	FILL CAP / DIPSTICK	FILLER CAP

STARTER

BUTTON

	PRIMER	RECOIL
		RECOIL
	SAFETY	STARTER
	SAFETY	HANDLE
	IGNITION	ON / OFF
	KEY	ON / OFF
	KEY	SWITCH
		SWITCH

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 20

10527SB-LS specifications

The Husqvarna 10527SB-LS is a powerful snow blower designed to tackle heavy snow accumulation with ease, making it a reliable choice for homeowners and professionals alike. This model is particularly noted for its impressive performance in harsh winter conditions, combining innovative technologies and user-friendly features to deliver efficiency and reliability.

One of the standout features of the Husqvarna 10527SB-LS is its robust 27-inch clearing width, making it capable of handling large areas quickly. The machine is powered by a strong, reliable engine that provides ample power to navigate through heavy, wet snow, ensuring that even the toughest winter storms are no match for its performance.

Equipped with a two-stage snow removal system, the 10527SB-LS excels in its ability to throw snow far from the path, thanks to its high-speed impeller. This two-stage process consists of an auger that gathers snow and ice, which is then discharged through a chute, effectively clearing driveways, sidewalks, and other surfaces. The adjustable chute enables users to direct the snow exactly where it is needed, enhancing the efficiency of the snow clearing process.

The snow blower’s heavy-duty construction is built to withstand the rigors of winter use. Its durable metal frame and components are designed to last, ensuring that the 10527SB-LS can tackle multiple seasons without significant wear. Additionally, the large, rugged tires provide excellent traction, enabling the machine to maneuver through snow and challenging terrains easily.

Comfort and usability are also key selling points for the Husqvarna 10527SB-LS. It features an ergonomic handle with controls easily accessible, allowing for smooth operations without straining the operator. The electric start function adds further convenience, allowing the operator to start the engine quickly with the push of a button rather than relying on a pull-cord system.

Safety is prioritized in the design of the 10527SB-LS, with features like an automatic safety shut-off in case of unexpected situations. This ensures that users can operate the snow blower with confidence.

Overall, the Husqvarna 10527SB-LS is a comprehensive snow removal solution that combines power, durability, and ease of use. Its range of features makes it well-equipped to handle the requirements of winter weather, making it an excellent investment for anyone looking to simplify their snow clearing tasks. Whether for a residential driveway or larger outdoor spaces, this snow blower stands out as an efficient and reliable tool.

Husqvarna 10527SB-LS Before Starting the Engine, Scraper BAR, To USE Drift Cutters See Fig

Models: 10527SB-LS