TO REMOVE WHEELS (See Fig. 24)

Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

KLIK PIN (INSTALL

OUTER HOLE

IN OUTER HOLE

 

OF AXLE ONLY)

 

AXLE

WHEEL

WHEEL HUB

FIG. 24

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

Remove safety ignition key; store it in a safe place.

Do not store gasoline from one season to another.

Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ex-

18 haust area is still warm.

Page 18
Image 18
Husqvarna 10527SB-LS owner manual Storage, Other

10527SB-LS specifications

The Husqvarna 10527SB-LS is a powerful snow blower designed to tackle heavy snow accumulation with ease, making it a reliable choice for homeowners and professionals alike. This model is particularly noted for its impressive performance in harsh winter conditions, combining innovative technologies and user-friendly features to deliver efficiency and reliability.

One of the standout features of the Husqvarna 10527SB-LS is its robust 27-inch clearing width, making it capable of handling large areas quickly. The machine is powered by a strong, reliable engine that provides ample power to navigate through heavy, wet snow, ensuring that even the toughest winter storms are no match for its performance.

Equipped with a two-stage snow removal system, the 10527SB-LS excels in its ability to throw snow far from the path, thanks to its high-speed impeller. This two-stage process consists of an auger that gathers snow and ice, which is then discharged through a chute, effectively clearing driveways, sidewalks, and other surfaces. The adjustable chute enables users to direct the snow exactly where it is needed, enhancing the efficiency of the snow clearing process.

The snow blower’s heavy-duty construction is built to withstand the rigors of winter use. Its durable metal frame and components are designed to last, ensuring that the 10527SB-LS can tackle multiple seasons without significant wear. Additionally, the large, rugged tires provide excellent traction, enabling the machine to maneuver through snow and challenging terrains easily.

Comfort and usability are also key selling points for the Husqvarna 10527SB-LS. It features an ergonomic handle with controls easily accessible, allowing for smooth operations without straining the operator. The electric start function adds further convenience, allowing the operator to start the engine quickly with the push of a button rather than relying on a pull-cord system.

Safety is prioritized in the design of the 10527SB-LS, with features like an automatic safety shut-off in case of unexpected situations. This ensures that users can operate the snow blower with confidence.

Overall, the Husqvarna 10527SB-LS is a comprehensive snow removal solution that combines power, durability, and ease of use. Its range of features makes it well-equipped to handle the requirements of winter weather, making it an excellent investment for anyone looking to simplify their snow clearing tasks. Whether for a residential driveway or larger outdoor spaces, this snow blower stands out as an efficient and reliable tool.