TO REMOVE WHEELS (See Fig. 23)

Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

KLIK PIN (INSTALL

OUTER HOLE

IN OUTER HOLE

 

OF AXLE ONLY)

 

AXLE

WHEEL

WHEEL HUB

FIG. 23

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

 

IMPORTANT: It is important to prevent gum deposits from

 

forming in essential fuel system parts such as carburetor,

 

fuel hose, or tank during storage. Also, alcohol blended fuels

 

(called gasohol or using ethanol or methanol) can attract

 

moisture which leads to separation and formation of acids

 

during storage. Acidic gas can damage the fuel system of

 

an engine while in storage.

18

 

Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

Do not store gasoline from one season to another.

Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ exhaust area is still warm.

Page 18
Image 18
Husqvarna 10530SBEB owner manual Storage, Other

10530SBEB specifications

The Husqvarna 10530SBEB is a powerful snow blower designed for both residential and light commercial use, delivering exceptional performance in winter conditions. One of its standout features is the robust 305cc engine that ensures reliable starting and consistent snow-clearing power. This engine provides ample torque, allowing the machine to handle heavy, wet snow with ease.

Equipped with a 30-inch clearing width, the 10530SBEB can efficiently tackle large areas, making it ideal for homeowners with expansive driveways and sidewalks. The high-throw chute can send snow up to 50 feet away, reducing the need for multiple passes and making snow removal quicker and more efficient. The adjustable chute rotation and deflector allow users to direct snow exactly where they want it, providing added flexibility during operation.

The Husqvarna 10530SBEB features an innovative overhead-valve engine design, which contributes to better fuel efficiency and lower emissions. This eco-conscious design aligns with Husqvarna’s commitment to sustainability while still providing high performance. The machine also includes a 6-speed forward and 1-speed reverse transmission, enabling users to choose the optimal speed for various snow conditions.

A major highlight of the 10530SBEB is its augmented throwing capability, aided by the integral turbocharge feature. This technology enhances the snow-throwing distance, making it effective even in heavier snow falls. The machine is also designed with a wide, heavy-duty auger that efficiently breaks up packed snow, ensuring better performance on tough surfaces.

User comfort is prioritized in the Husqvarna 10530SBEB, featuring an ergonomic handle that reduces fatigue during extended use. The handle is also adjustable, accommodating users of different heights. For visibility, the snow blower comes with integrated LED headlights, allowing for safe operation in low-light conditions.

Durability is another key characteristic of the 10530SBEB, with its rugged construction designed to withstand tough winter conditions. The steel housing and reinforced components ensure longevity, while the easily accessible control panel simplifies operation for users of all experience levels.

Overall, the Husqvarna 10530SBEB is a versatile and robust snow blower that combines power, efficiency, and user-friendly features, making it a reliable choice for tackling winter’s challenges. Whether facing light flurries or heavy snowfalls, this model stands out as an excellent tool for snow removal, ensuring that driveways and walkways remain clear and safe.