Manuals / Husqvarna / Lawn and Garden / Chainsaw

Husqvarna 115 13 81-26 manual Assembly, Fitting a spike bumper

Models: 115 13 81-26

1 44

Download 44 pages 16.83 Kb

Page 18

Fitting a spike bumper

ASSEMBLY

Fit the bar over the bar bolts. Place the bar in its rearmost position. Place the chain over the drive sprocket locate it in the groove on the bar. Begin on the top edge of the bar.

Make sure that the edges of the cutting links are facing forward on the top edge of the bar.

Fit the clutch cover and locate the chain adjuster pin in the hole in the bar. Check that the drive links of the chain ﬁt correctly over the drive sprocket and that the chain is correctly located in the groove in the bar.

Tension the chain by turning the wheel down (+). The chain should be tensioned until it does not sag from the underside of the bar.

The chain is correctly tensioned when it does not sag from the underside of the bar, but can still be turned easily by hand. Hold up the bar tip and tighten the bar knob by turning the knob clockwise.

When ﬁtting a new chain, the chain tension has to be checked frequently until the chain is run-in. Check the chain tension regularly. A correctly tensioned chain ensures good cutting performance and long life.

Fitting a spike bumper

To ﬁt a spike bumper – contact your service agent.

18 – English

115 13 81-26 Rev.3 2009-01-14

Image 18

Husqvarna 115 13 81-26 manual Assembly, Fitting a spike bumper

Contents

Operator′s manual 445 445e 450eKEY TO SYMBOLS Symbols on the machineSymbols in the operator’s manual CONTENTS ContentsINTRODUCTION Dear CustomerWHAT IS WHAT? What is what on the chain saw?GENERAL SAFETY PRECAUTIONS Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense GENERAL SAFETY PRECAUTIONSGENERAL SAFETY PRECAUTIONS 8 - EnglishGENERAL SAFETY PRECAUTIONS Throttle lockoutRight hand guard GENERAL SAFETY PRECAUTIONSStop switch Vibration damping systemGeneral rules Cutting equipmentGENERAL SAFETY PRECAUTIONS Cutting equipment designed to reduce kickbackGeneral information on sharpening cutting teeth GENERAL SAFETY PRECAUTIONSChain WARNING! Departure from theincreased if the depth gauge setting is GENERAL SAFETY PRECAUTIONSGeneral advice on adjusting depth gauge setting Adjustment of depth gauge settingGENERAL SAFETY PRECAUTIONS 445e, 450ewhich could lead to serious, even fatal injuries GENERAL SAFETY PRECAUTIONSLubricating cutting equipment Chain oilGENERAL SAFETY PRECAUTIONS Chain drive sprocketASSEMBLY Fitting the bar and chainASSEMBLY Fitting a spike bumperFUEL HANDLING FuelFUEL HANDLING Fuel safetyFuelling Transport and storageSTARTING AND STOPPING Starting and stoppingSTARTING AND STOPPING StoppingWORKING TECHNIQUES Before useGeneral working instructions WORKING TECHNIQUES 24 - EnglishWORKING TECHNIQUES Basic cutting techniqueWORKING TECHNIQUES Tree felling techniqueClearing the trunk and preparing your retreat WORKING TECHNIQUESFelling direction FellingWORKING TECHNIQUES Felling cutWORKING TECHNIQUES How to avoid kickbackWhat is kickback? Freeing a tree that has fallen badlyWORKING TECHNIQUES Limbing WARNING! A majority of kickbackMAINTENANCE Carburettor adjustmentGeneral Checking the brake trigger MAINTENANCEChecking the inertia brake release immediatelyMufﬂer MAINTENANCEReplacing the starter cord StarterMAINTENANCE Tensioning the recoil springReplacing the return and drive springs Air ﬁlterMAINTENANCE Fitting the starterNeedle bearing lubrication Spark plugLubricating the bar tip sprocket Cooling systemMAINTENANCE ”Air Injection” centrifugal cleaningWinter use Temperature -5Cor colderDaily maintenance Maintenance scheduleMAINTENANCE Weekly maintenanceTECHNICAL DATA Technical dataTECHNICAL DATA Bar and chain combinationsSaw chain ﬁling and ﬁle gauges ChainEC-declarationof conformity TECHNICAL DATAApplies to Europe only ´z+SF,¶6+¨ ´z+SF,¶6+¨ 115 13 81-26Rev.3115 13 81-26Rev.3 ´z+SF,¶6+¨ ´z+SF,¶6+¨ 115 13 81-26Rev.3