Manuals / Husqvarna / Lawn and Garden / Snow Blower

Husqvarna 1827EXLT warranty Service And Adjustments, Engine, TO REMOVE TRACKS See Fig, Carburetor

Models: 1827EXLT

1 28

Download 28 pages 15.89 Kb

Page 20

TO REMOVE TRACKS (See Fig. 27)

SERVICE AND ADJUSTMENTS

TO REMOVE TRACKS (See Fig. 27)

•Remove the klik pin and remove track from axle.

HOLE

KLIK PIN

AXLE

TRACK

TRACK HUB

FIG. 27

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

TO ADJUST CABLE TENSION (See Fig. 28)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 28

20

Image 20

Husqvarna 1827EXLT warranty Service And Adjustments, TO REMOVE TRACKS See Fig, Carburetor, Engine Speed

Contents

Operator’s Manual 1827EXLTEnglish 532Safe Operation Practices for Walk-Behind Snow Throwers TrainingPreparation OperationMaintenance and Storage Clearing a Clogged Discharge ChuteTABLE OF CONTENTS PRODUCT SPECIFICATIONSCUSTOMER RESPONSIBILITIES SERVICE AND ADJUSTMENTSPARTS PACKED SEPARATELY IN CARTON 1806846 SHEAR BOLTS 1/4-20 x 1-3/4 443059ASSEMBLY / PRE-OPERATION HOW TO SET UP YOUR SNOW THROWERREMOVE SNOW THROWER FROM CARTON INSTALL SPEED CONTROL ROD See Figs. 1 andINSTALL AUGER CONTROL ROD See Figs. 5 and ASSEMBLY / PRE-OPERATIONINSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and ASSEMBLY / PRE-OPERATION INSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD See FigINSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8 and ALIGN BEFOREOPERATION KNOW YOUR SNOW THROWERRecoil auxiliary starter handle - used for starting engine MEETS A.N.S.I. SAFETY REQUIREMENTSOPERATION TRANSPORT AND HEIGHT ADJUSTMENT OF SNOW THROWER HOW TO USE YOUR SNOW THROWERSET HEIGHT ADJUSTMENT See Figs OPERATIONUSING THE CLEAN-OUT TOOL See Fig OPERATIONTO USE FUEL SHUT-OFF VALVE See Fig TO USE CHOKE CONTROL See FigPOWER STEERING OPERATION See Fig TO ADJUST SKID PLATES See FigOPERATION TO MOVE FORWARD AND BACKWARD See FigBEFORE STARTING THE ENGINE OPERATIONTO USE DRIFT CUTTERS See Fig CHECK ENGINE OIL LEVEL See FigSNOW THROWING TIPS OPERATIONBEFORE STOPPING IF RECOIL STARTER HAS FROZENMAINTENANCE GENERAL RECOMMENDATIONSBEFORE EACH USE LUBRICATIONCLEANING SNOW THROWERENGINE MAINTENANCESERVICE AND ADJUSTMENTS 1. Be sure the on/off switch is in the OFF position2. Remove safety ignition key TO ADJUST SNOW THROWER HEIGHTSERVICE AND ADJUSTMENTS TO REPLACE BELTS See FigSERVICE AND ADJUSTMENTS TO ADJUST CABLE TENSION See FigENGINE TO REMOVE TRACKS See FigSTORAGE OTHERSNOW THROWER ENGINETROUBLESHOOTING PROBLEMCAUSE CORRECTIONConVumer Wheeled ProductV ‒ Limited WDrrDnty LIMITATIONS AND EXCLUSIONSHOW TO OBTAIN SERVICE +DUULV&RUQHUV3DUNZD\&KDUORWWH1&Consumer Wheeled Warranty Chart Product/ComponentQJLQH ConsumerConsumer Wheeled Warranty Chart Product/ComponentConsumer EZ One 1 Year Commercial Zarranty, parts & labor, Zith HusqvarnaSERVICE NOTES 08/01/2011 SR