Manuals / Husqvarna / Lawn and Garden / Snow Blower

Husqvarna 1827EXLT Assembly / Pre-Operation, INSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and

Models: 1827EXLT

1 28

Download 28 pages 15.89 Kb

Page 7

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

ASSEMBLY / PRE-OPERATION

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod is installed on the snow thrower.

1.Remove plastic tie securing rod to lower handle.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

PLASTIC TIE

TRACTION DRIVE

CONTROL ROD

VINYL

SLEEVE

FIG. 3

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING

TRACTION

DRIVE

CONTROL

ROD

DRIVE

CONTROL

BRACKET

FIG. 4

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

1.Retrieve vinyl sleeve and spring from bag of parts and retrieve the auger control rod from carton chute tray. Slide straight rod end through the small hole in the vinyl sleeve. Hook spring in hole in rod end.

2.Hook end of spring into control arm with loop opening up as shown. (See Fig. 5)

3.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

	AUGER
	CONTROL
	ROD
	VINYL
CONTROL	SLEEVE
CONTROL
ARM
	LOOP
	OPENING
	UP

FIG. 5

	AUGER CONTROL ROD	AUGER
	RETAINER	CONTROL
	RETAINER	LEVER
	SPRING	LEVER
	SPRING
		AUGER
	CONTROL
	BRACKET

FIG. 6

7

Image 7

Husqvarna 1827EXLT warranty Assembly / Pre-Operation, INSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and

Contents

532 Operator’s Manual1827EXLT EnglishOperation Safe Operation Practices for Walk-Behind Snow ThrowersTraining PreparationClearing a Clogged Discharge Chute Maintenance and StorageSERVICE AND ADJUSTMENTS TABLE OF CONTENTSPRODUCT SPECIFICATIONS CUSTOMER RESPONSIBILITIES443059 PARTS PACKED SEPARATELY IN CARTON180684 6 SHEAR BOLTS 1/4-20 x 1-3/4INSTALL SPEED CONTROL ROD See Figs. 1 and ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER REMOVE SNOW THROWER FROM CARTONINSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and ASSEMBLY / PRE-OPERATIONINSTALL AUGER CONTROL ROD See Figs. 5 and ALIGN BEFORE ASSEMBLY / PRE-OPERATIONINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD See Fig INSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8 andKNOW YOUR SNOW THROWER OPERATIONOPERATION MEETS A.N.S.I. SAFETY REQUIREMENTSRecoil auxiliary starter handle - used for starting engine OPERATION TRANSPORT AND HEIGHT ADJUSTMENT OF SNOW THROWERHOW TO USE YOUR SNOW THROWER SET HEIGHT ADJUSTMENT See FigsTO USE CHOKE CONTROL See Fig USING THE CLEAN-OUT TOOL See FigOPERATION TO USE FUEL SHUT-OFF VALVE See FigTO MOVE FORWARD AND BACKWARD See Fig POWER STEERING OPERATION See FigTO ADJUST SKID PLATES See Fig OPERATIONCHECK ENGINE OIL LEVEL See Fig BEFORE STARTING THE ENGINEOPERATION TO USE DRIFT CUTTERS See FigIF RECOIL STARTER HAS FROZEN SNOW THROWING TIPSOPERATION BEFORE STOPPINGLUBRICATION MAINTENANCEGENERAL RECOMMENDATIONS BEFORE EACH USEMAINTENANCE CLEANINGSNOW THROWER ENGINETO ADJUST SNOW THROWER HEIGHT SERVICE AND ADJUSTMENTS1. Be sure the on/off switch is in the OFF position 2. Remove safety ignition keyTO REPLACE BELTS See Fig SERVICE AND ADJUSTMENTSTO REMOVE TRACKS See Fig SERVICE AND ADJUSTMENTSTO ADJUST CABLE TENSION See Fig ENGINEENGINE STORAGEOTHER SNOW THROWERCORRECTION TROUBLESHOOTINGPROBLEM CAUSELIMITATIONS AND EXCLUSIONS ConVumer Wheeled ProductV ‒ Limited WDrrDnty+DUULV&RUQHUV3DUNZD\&KDUORWWH1& HOW TO OBTAIN SERVICEConsumer Consumer Wheeled Warranty ChartProduct/Component QJLQHEZ One 1 Year Commercial Zarranty, parts & labor, Zith Husqvarna Consumer Wheeled Warranty ChartProduct/Component ConsumerSERVICE NOTES 08/01/2011 SR