MAINTENANCE
Move the front hand guard forwards and back to make sure it moves freely and that it is securely anchored to the clutch cover. (47)
Checking the inertia brake release
Place the chain saw, with the engine switched off, on a stump or other stable surface. Release the front handle and let the saw fall by its own weight, rotating around the rear handle towards the stump.
When the bar hits the stump the brake should be applied. (48)
Checking the
Check that the right hand guard is not damaged and that there are no visible defects, such as cracks.
Push the trigger up and forwards to check that it moves freely and is securely hinged to the clutch cover.
Never carry or hang the saw by the trigger! This could damage the mechanism and disable the chain brake. (49)
Checking the brake trigger
Place the chain saw on firm ground and start it. Make sure the chain does not touch the ground or any other object. See the instructions under the heading Start and stop. Grasp the chain saw firmly, wrapping your fingers and thumbs around the handles.
Apply full throttle and activate the chain brake by tilting your left wrist forward onto the front hand guard. Do not let go of the front handle. The chain should stop immediately.
Throttle lockout
•Make sure the throttle control is locked at the idle setting when the throttle lockout is released.
•Press the throttle lockout and make sure it returns to its original position when you release it.
•Check that the throttle control and throttle lockout move freely and that the return springs work properly.
•Start the chain saw and apply full throttle. Release the throttle control and check that the chain stops and remains stationary. If the chain rotates when the throttle control is in the idle position you should check the carburettor idle adjustment.
Chain catcher
Check that the chain catcher is not damaged and is firmly attached to the body of the chain saw.
Right hand guard
Check that the right hand guard is not damaged and that there are no visible defects, such as cracks.
Vibration damping system
Regularly check the vibration damping units for cracks or deformation.
Make sure the vibration damping units are securely attached to the engine unit and handle unit.
Stop switch
Start the engine and make sure the engine stops when you move the stop switch to the stop setting.
Muffler
Never use a machine that has a faulty muffler. Regularly check that the muffler is securely attached to the machine.
Note: The spark arrestor screen (A) on this machine is serviceable. (50) The mesh must be replaced if it is damaged. If the mesh is blocked the machine will overheat and this will cause damage to the cylinder and piston. Never use a machine with a muffler that is in poor condition. Never use a muffler if the spark arrestor mesh is missing or defective.
For normal homeowner use, the muffler and spark arresting screen will not require replacement. After 75 hours of use, we recommend that your muffler be replaced by your authorized Husqvarna service dealer.
Air filter
The air filter must be regularly cleaned to remove dust and dirt in order to avoid:
•Carburettor malfunctions
•Starting problems
•Loss of engine power
•Unnecessary wear to engine parts.
•Excessive fuel consumption.
•Remove the air filter (3) after taking off the cylinder cover, screw (1) and filter cover (2). When refitting make sure that the air filter seals tightly against the filter
holder. Clean the filter by brushing or shaking it. (51) The filter can be cleaned more thoroughly by washing it in water and detergent.
An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced.
A HUSQVARNA chain saw can be equipped with different types of air filter according to working conditions, weather, season, etc. Contact your dealer for advice.
Spark plug
The spark plug condition is influenced by:
•Incorrect carburettor adjustment.
•An incorrect fuel mixture (too much or incorrect type of oil).
•A dirty air filter.
These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.
If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.5 mm. The spark plug should be replaced after about a month in operation or earlier if necessary. (52)
Note! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor.
20 – English | |
|
