Manuals / Husqvarna / Lawn and Garden / Chainsaw

Husqvarna 385XP manual Bar and chain combinations, Saw chain ﬁling and ﬁle gauges

Models: 385XP

1 44

Download 44 pages 57.99 Kb

Page 40

Image 40

TECHNICAL DATA

Bar and chain combinations

The following combinations are CE approved.

		Bar			Chain

Length, inch	Pitch, inch	Gauge, mm	Max. nose radius	Type		Length, drive links
Length, inch	Pitch, inch	Gauge, mm	Max. nose radius	Type		(no.)
						(no.)

18	3/8	1,5	11T	Husqvarna H42,		68
				Husqvarna H48,
20	3/8	1,5	11T	Husqvarna H48,		72
20	3/8	1,5	11T	Husqvarna H81		72

24	3/8	1,5	11T			84
24	3/8	1,5	11T			84

28	3/8	1,5	11T			92

The combinations below are not CE type approved, but are recommended for 390XP/XPG on markets outside of Europe, which do not demand special type approval.

		Bar	Chain

Length, inch	Pitch, inch	Max. number of teeth on tip sprocket /radius of tip	Type
Length, inch	Pitch, inch	sprocket	Type
		sprocket

24	0,404	34 mm	Husqvarna H64

28	0,404	34 mm

32	0,404	42 mm

36	0,404	42 mm

Saw chain ﬁling and ﬁle gauges

40 – English

Page 40

Image 40

Husqvarna 385XP manual Bar and chain combinations, Saw chain ﬁling and ﬁle gauges

Contents

385XP 390XP Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Chain catcher Throttle lockRight hand guard Stop switch Cutting equipmentVibration damping system MufﬂerGeneral rules Cutting equipment designed to reduce kickbackBar ChainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingSharpening cutting teeth General advice on adjusting depth gauge setting Adjustment of depth gauge settingIf the depth gauge setting is too large Tensioning the chainLubricating cutting equipment Chain oilFilling with chain oil Checking chain lubricationNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Assembly Fitting the bar and chainFitting a spike bumper Working with the chainFuel Handling FuelFuel safety FuellingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsAlways use a fast cutting speed, i.e. full throttle General Basic cutting techniqueTerms Limbing CuttingTree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts FellingFelling cut General advice Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Maintenance Carburettor adjustmentGeneral Carburettor with movement limitersFine adjustment of the idle speed T Correctly adjusted carburettorCarburettor without movement limiters Low speed jet LChecking brake band wear When the bar hits the stump the brake should be applied Checking the front hand guardChecking the inertia brake release Checking the brake triggerMufﬂer Starter Changing a broken or worn starter cordTensioning the recoil spring Changing a broken recoil springAir ﬁlter Spark plugLubricating the bar tip sprocket Fitting the starterAdjustment of the oil pump Air Injection centrifugal cleaningNeedle bearing lubrication Cooling systemTemperature 0C or colder Heated handlesElectrical carburettor heating 385XPG, 390XPGMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain ﬁling and ﬁle gaugesApplies to Europe only EC-declaration of conformityEN ISO 12100-22003, Cispr 121997, ISO ´z+R16¶6a¨ Page 1150172-26 ´z+R16¶6a¨ ´z+R16¶6a¨