Cisco Systems IE 3010 specs

Appendix C Configuring the Switch with the CLI Setup Program

Accessing the CLI Through the Console Port

Step 5 Configure the COM port.

Step 6 Configure the baud rate and character format of the PC or terminal to match the console port characteristics:

•9600 baud

•8 data bits

•1 stop bit

•No parity

•None (flow control)

Step 7 Connect power to the switch as described in Chapter 3, “Power Supply Installation.”

Step 8 The PC or terminal displays the bootloader sequence. Press Enter to display the setup prompt. Follow the steps in the “Completing the Setup Program” section on page C-7.

Installing the Cisco Microsoft Windows USB Device Drivers

Installing the Cisco Microsoft Windows XP USB Driver

Step 1 Obtain the file Cisco_usbconsole_driver.zip from Cisco.com, and unzip it.

Note You can download the driver file from the Cisco.com software download site.

Step 2 If using 32-bit Windows XP, double-click the setup.exe file in the Windows_32 folder. If using 64-bit Windows XP, double-click the setup(x64).exe file in the Windows_64 folder.

Step 3 The Cisco Virtual Com InstallShield Wizard begins.

Step 4 The Ready to Install the Program window appears. Click Install.

Step 5 The InstallShield Wizard Completed window appears. Click Finish.

Step 6 Connect the USB cable to the PC and to the switch console port. The USB console port LED turns green, and the Found New Hardware Wizard appears. Follow the instructions to complete the driver installation.

Installing the Cisco Microsoft Windows 2000 USB Driver

			Step 1	Obtain the file Cisco_usbconsole_driver.zip from Cisco.com, and unzip it.

				Note		You can download the driver file from the Cisco.com software download site.

			Step 2	Double-click the setup.exe file.
			Step 3	The Cisco Virtual Com InstallShield Wizard begins. Click Next.
			Step 4	The Ready to Install the Program window appears. Click Install.
			Cisco IE 3010 Switch Hardware Installation Guide
			Cisco IE 3010 Switch Hardware Installation Guide

	C-4					78-19581-02
	C-4					78-19581-02

Image 88

Cisco Systems IE 3010 manual Installing the Cisco Microsoft Windows USB Device Drivers

Contents

Cisco IE 3010 Switch Hardware Installation Guide Americas HeadquartersPage N T E N T S Wall-Mounting2-15 Power-Supply Module Specifications A-4 Accessing the CLI Through the Console Port C-1 Preface Obtaining Documentation and Submitting a Service Request Related Publications Switch Models Model Description Cable Side Cisco IE-3010-24TC Cable-Side View 10/100 Fast Ethernet Ports PoE Ports Dual-Purpose Ports SFP Modules Type of SFP Module Model Alarm Ports Power-Input TerminalSFP Module Patch Cable Alarm Output Alarm InputManagement Ports Switch Panel LEDs LEDs Power-Supply Module LEDs Alarm LEDsSystem LED Color System Status Console LEDs Port LEDsColor Description LED Color Meaning SD Flash Memory Card PoE LEDDual-Purpose Port LEDs SD Flash Memory Card LED Power-Supply Side PSU OK LED Power-Supply Side LEDs USB LED Network Configurations Power Supply FeaturesManagement Options Switch Installation 75 in .4 cm. Statement Installation Guidelines Verifying Switch Operation Installing the Switch Rack-Mounting 1and -2show how to attach brackets to the switches Attaching Brackets for 19-Inch Racks 207231 Rubber plug Switch Inserting the Rubber Plugs 255740 255750 255751 Attaching Brackets for 23-Inch Racks Attaching 23-Inch Brackets Attaching Brackets for Etsi Racks Attaching Brackets for Etsi Racks Rack-Mounting the Switch Wall-Mounting Attaching Brackets Attaching Brackets for IP-30 Compliance Optional Rubber plug Switch-side Wall-Mounting the Switch User-supplied screws 15 Wall-Mounting the Cisco IE-3010-16S-8PC Installing and Removing SFP Modules Installing SFP Modules Inserting and Removing the SFP Module Patch Cable Removing SFP Modules Removing the SFP Module Patch Cable 18 Inserting an SFP Module Patch Cable Replacing the SD Flash Memory Card 20 Loosening the Captive Screw 22 Removing the SD Flash Memory Card Connecting Devices to the Ethernet Ports Connecting to the 10/100 and 10/100/1000 Ports Connecting to the 10/100 PoE Ports Device Crossover Cable Where to Go Next Page Power Supply Installation Power-Supply Modules Power-supply module 3 Captive screw Power-Supply Module Installation Installation Guidelines Grounding the Switch Installing a Power-Supply ModuleEquipment That You Need Stripping the Ground Wire Installing the Power-Supply Module in the Switch Crimping the Terminal Lug Wiring the Power Source Loosen the Screws on the Power Supply Blank Opening the Power-Input Terminal Cover AC 5 A, DC 15 a Statement 100-240V~, 50-60Hz, 2A 10A 10A 11 Stripping the Input Power Source Wire 13 Connecting the Wires to the High-Voltage AC Power PSU1 Removing the Power-Supply Module AC power 16 Removing the Power-Supply Module Page Diagnosing Problems Switch Post Results Switch LEDs Switch ConnectionsBad or Damaged Cable Ethernet and Fiber-Optic Cables Interface Settings 10/100 and 10/100/1000 Port Connections10/100 PoE Port Connections SFP Module Switch Performance Spanning Tree LoopsSpeed, Duplex, and Autonegotiation Autonegotiation and Network Interface Cards Resetting the Switch to the Factory Default Settings Finding the Switch Serial Number Serial Number Location for the Power-Supply Modules Physical Specifications Switch SpecificationsEnvironmental Ranges Power Requirements Power Requirements Power-Supply Module Specifications Power Specifications Alarm Ratings Page Connector Specifications 10/100 SFP Module Connectors Figure B-2 Fiber-Optic SFP Module LC Connector Alarm Port Pin Alarm connection Cables and Adapters SFP Module Cables Extended temperature SFPs GLC-EX-SMD Cable Pinouts TP3 Console Port Adapter Pinouts DSR DTR CTS RTS Switch Console RJ-45-to-DB-25 Port DTE Adapter Device Accessing the CLI Through the Console Port RJ-45 Console Port Figure C-1 Connecting the Console Cable Figure C-2 Connecting the USB Console Cable USB Console Port Installing the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows USB Device DriversInstalling the Cisco Microsoft Windows 2000 USB Driver Uninstalling the Cisco Microsoft Windows USB Drivers Installing the Cisco Microsoft Windows Vista USB Driver Uninstalling the Cisco Microsoft Windows Vista USB Driver Using the Setup.exe Program IP Settings Entering the Initial Configuration InformationCompleting the Setup Program Enter virtual terminal password terminal-password These choices appear Cisco IE 3010 Switch Hardware Installation Guide Numerics IN-2 IN-3 IN-4 IN-5 IN-6