Cisco Systems IE 3010 - page 59

3-9

Cisco IE 3010 Switch Hardware Installation Guide

78-19581-02

Chapter 3 Power Supply Installation

Power-Supply Module Installation

Figure 3-10 Power-Input Terminal

Note The power-supply module 1 connection is labeled PSU1, and the power-supply module 2 connection is

labeled PSU2. Make sure that you connect the wires to the correct terminal screws.

Step 3 Use twisted-pair copper wire (14- to 18-AWG) to connect from the power-input terminal to the power

source.

Note Use 12-AWG (minimum) for the low-voltage DC power supply module. Use 16-AWG

(minimum) for the high-voltage AC or DC power supply module.

Step 4 Strip each of the two wires to 0.25 inch (6.3 mm) ± 0.02 inch (0.5 mm). Do not strip more than 0.27 inch

(6.8 mm) of insulation from the wire. Stripping more than the recommended amount of wire can leave

exposed wire from the connector after installation.

1Line connection for high-voltage AC (PSU1) 8Line connection for high-voltage AC (for

PSU2)

2Neutral connection for high-voltage AC

(PSU1)

9Neutral connection for high-voltage AC

(PSU2)

3Positive connection for high-voltage DC

(PSU1)

10 Positive connection for high-voltage DC

(PSU2)

4Negative connection for high-voltage DC

(PSU1)

11 Negative connection for high-voltage DC

(PSU2)

5PSU1 (power-supply module 1) 12 PSU2 (power-supply module 2)

6Positive connection for low-voltage DC

(PSU1)

13 Positive connection for low-voltage DC

(PSU2)

7Negative connection for low-voltage DC

(PSU1)

14 Negative connection for low-voltage DC

(PSU2)

100-240V~, 50-60Hz, 2A

5

100-240V~, 50-60Hz, 2A

2A2A

10A

10A

5

2

1

4

3

76

98

11

10

14

13

512

207241

Contents

Main Page CONTENTS Page Page Page Preface Related Publications Obtaining Documentation and Submitting a Service Request Product Overview Switch Models Cable Side 7 4 92 1 3 5 6 8 10/100 Fast Ethernet Ports PoE Ports 8 4102 1 3 65 7 9 Dual-Purpose Ports SFP Modules SFP Module Patch Cable Power-Input Terminal Alarm Ports Alarm Input Alarm Output Management Ports LEDs Switch Panel LEDs 14 15 16 21 3456789 10 11 12 13 System LED Power-Supply Module LEDs Alarm LEDs Console LEDs Port LEDs PoE LED Dual-Purpose Port LEDs SD Flash Memory Card LED SD Flash Memory Card Power-Supply Side Power-Supply Side LEDs 21 3456789 10 11 12 1314 15 Power Supply Features Management Options Network Configurations Switch Installation Warnings 2-2 Installation Guidelines Verifying Switch Operation Installing the Switch Rack-Mounting Attaching Brackets for 19-Inch Racks Attaching Brackets for 19-Inch Racks for IP-30 Compliance (Optional) Page Page Page Page Page Attaching Brackets for 23-Inch Racks Attaching Brackets for ETSI Racks Rack-Mounting the Switch Wall-Mounting Attaching Brackets Attaching Brackets for IP-30 Compliance (Optional) Page Wall-Mounting the Switch Page Installing and Removing SFP Modules Installing SFP Modules Removing SFP Modules Inserting and Removing the SFP Module Patch Cable 2-22 Cisco IE 3010 Switch Hardware Installation Guide 78-19581-02 Cisco IE 3010 Chapter 2 Switch Installation Inserting and Removing the SFP Module Patch Cable Removing the SFP Module Patch Cable Cisco IE 3010 Cisco IE 3010 Replacing the SD Flash Memory Card Page Connecting Devices to the Ethernet Ports Connecting to the 10/100 and 10/100/1000 Ports Connecting to the 10/100 PoE Ports Page Page Power Supply Installation Power-Supply Modules Page Power-Supply Module Installation Installation Guidelines Installing a Power-Supply Module Equipment That You Need Grounding the Switch Page Installing the Power-Supply Module in the Switch Wiring the Power Source 3-8 The terminal screws labels are on the power-input terminal cover. See Figure 3-10. Page Page Page Removing the Power-Supply Module Page Page Troubleshooting Diagnosing Problems Switch POST Results Switch LEDs Switch Connections Bad or Damaged Cable Ethernet and Fiber-Optic Cables Link Status 10/100 and 10/100/1000 Port Connections 10/100 PoE Port Connections SFP Module Interface Settings Ping End Device Switch Performance Speed, Duplex, and Autonegotiation Autonegotiation and Network Interface Cards Cabling Distance Resetting the Switch to the Factory Default Settings Finding the Switch Serial Number Page A Technical Specifications Switch Specifications Page Page Power-Supply Module Specifications Alarm Ratings Page B Connector and Cable Specifications Connector Specifications 10/100 SFP Module Connectors B-3 Dual-Purpose Ports The 10/100/1000 Ethernet ports on the dual-purpose ports use RJ-45 connectors. Alarm Port Cables and Adapters SFP Module Cables Page B-6 Cable Pinouts Console Port Adapter Pinouts Page C Configuring the Switch with the CLI Setup Program Accessing the CLI Through the Console Port RJ-45 Console Port Page USB Console Port Installing the Cisco Microsoft Windows USB Device Drivers Installing the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows 2000 USB Driver Installing the Cisco Microsoft Windows Vista USB Driver Uninstalling the Cisco Microsoft Windows USB Drivers Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver Using the Add or Remove Programs Utility Using the Setup.exe Program Uninstalling the Cisco Microsoft Windows Vista USB Driver Entering the Initial Configuration Information IP Settings Completing the Setup Program Page Page Page INDEX Numerics A C D E G H M O P R T U W