Power-Supply Module Installation | Cisco Systems IE 3010 specs

Chapter 3 Power Supply Installation

Power-Supply Module Installation

Power-Supply Module Installation

•Installation Guidelines, page 3-3

•Installing a Power-Supply Module, page 3-4

•Wiring the Power Source, page 3-7

•Removing the Power-Supply Module, page 3-12

Installation Guidelines

Observe these guidelines when removing or installing a power-supply module:

A power-supply module that is only partially connected to the switch disrupts the system operation.

Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029

Note You can order the blank cover (part number RPS-CG-COVER=).

Warning Do not reach into a vacant slot while installing or removing a module. Exposed circuitry is an energy hazard. Statement 206

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030

Warning Avoid using or servicing any equipment that has outdoor connections during an electrical storm. There may be a risk of electric shock from lightning. Statement 1088

Cisco IE 3010 Switch Hardware Installation Guide

	78-19581-02	3-3

Image 53

Cisco Systems IE 3010 manual Power-Supply Module Installation, Installation Guidelines

Contents

Americas Headquarters Cisco IE 3010 Switch Hardware Installation GuidePage N T E N T S Wall-Mounting2-15 Power-Supply Module Specifications A-4 Accessing the CLI Through the Console Port C-1 Preface Related Publications Obtaining Documentation and Submitting a Service Request Model Description Switch Models Cisco IE-3010-24TC Cable-Side View Cable Side PoE Ports 10/100 Fast Ethernet Ports Dual-Purpose Ports Type of SFP Module Model SFP Modules SFP Module Patch Cable Power-Input TerminalAlarm Ports Management Ports Alarm InputAlarm Output LEDs Switch Panel LEDs Alarm LEDs Power-Supply Module LEDsSystem LED Color System Status Port LEDs Console LEDsColor Description LED Color Meaning PoE LED SD Flash Memory CardDual-Purpose Port LEDs SD Flash Memory Card LED PSU OK LED Power-Supply Side USB LED Power-Supply Side LEDs Management Options Power Supply FeaturesNetwork Configurations Switch Installation 75 in .4 cm. Statement Verifying Switch Operation Installation Guidelines Rack-Mounting Installing the Switch Attaching Brackets for 19-Inch Racks 1and -2show how to attach brackets to the switches 207231 Rubber plug Switch Inserting the Rubber Plugs 255740 255750 255751 Attaching 23-Inch Brackets Attaching Brackets for 23-Inch Racks Attaching Brackets for Etsi Racks Attaching Brackets for Etsi Racks Rack-Mounting the Switch Wall-Mounting Attaching Brackets for IP-30 Compliance Optional Attaching Brackets Rubber plug Switch-side User-supplied screws Wall-Mounting the Switch 15 Wall-Mounting the Cisco IE-3010-16S-8PC Installing SFP Modules Installing and Removing SFP Modules Removing SFP Modules Inserting and Removing the SFP Module Patch Cable 18 Inserting an SFP Module Patch Cable Removing the SFP Module Patch Cable 20 Loosening the Captive Screw Replacing the SD Flash Memory Card 22 Removing the SD Flash Memory Card Connecting to the 10/100 and 10/100/1000 Ports Connecting Devices to the Ethernet Ports Device Crossover Cable Connecting to the 10/100 PoE Ports Where to Go Next Page Power-Supply Modules Power Supply Installation Power-supply module 3 Captive screw Installation Guidelines Power-Supply Module Installation Equipment That You Need Installing a Power-Supply ModuleGrounding the Switch Stripping the Ground Wire Crimping the Terminal Lug Installing the Power-Supply Module in the Switch Loosen the Screws on the Power Supply Blank Wiring the Power Source AC 5 A, DC 15 a Statement Opening the Power-Input Terminal Cover 100-240V~, 50-60Hz, 2A 10A 10A 11 Stripping the Input Power Source Wire 13 Connecting the Wires to the High-Voltage AC Power PSU1 AC power Removing the Power-Supply Module 16 Removing the Power-Supply Module Page Switch Post Results Diagnosing Problems Switch Connections Switch LEDsBad or Damaged Cable Ethernet and Fiber-Optic Cables 10/100 and 10/100/1000 Port Connections Interface Settings10/100 PoE Port Connections SFP Module Spanning Tree Loops Switch PerformanceSpeed, Duplex, and Autonegotiation Autonegotiation and Network Interface Cards Finding the Switch Serial Number Resetting the Switch to the Factory Default Settings Serial Number Location for the Power-Supply Modules Environmental Ranges Switch SpecificationsPhysical Specifications Power Requirements Power Requirements Power Specifications Power-Supply Module Specifications Alarm Ratings Page 10/100 Connector Specifications Figure B-2 Fiber-Optic SFP Module LC Connector SFP Module Connectors Pin Alarm connection Alarm Port SFP Module Cables Cables and Adapters GLC-EX-SMD Extended temperature SFPs TP3 Cable Pinouts DSR DTR CTS RTS Console Port Adapter Pinouts Switch Console RJ-45-to-DB-25 Port DTE Adapter Device RJ-45 Console Port Accessing the CLI Through the Console Port Figure C-1 Connecting the Console Cable USB Console Port Figure C-2 Connecting the USB Console Cable Installing the Cisco Microsoft Windows 2000 USB Driver Installing the Cisco Microsoft Windows USB Device DriversInstalling the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows Vista USB Driver Uninstalling the Cisco Microsoft Windows USB Drivers Using the Setup.exe Program Uninstalling the Cisco Microsoft Windows Vista USB Driver Completing the Setup Program Entering the Initial Configuration InformationIP Settings Enter virtual terminal password terminal-password These choices appear Cisco IE 3010 Switch Hardware Installation Guide Numerics IN-2 IN-3 IN-4 IN-5 IN-6