Husqvarna manual Starting and Stopping, Mowing, Environmental Information, Royal 43ELS K

STARTING AND STOPPING

Cable Restraint
1. Form loop in mains cable and push the loop
through the slot as illustrated in picture	G1.

2.To secure, position loop over the hook and pull the cable back through the slot as illustrated in

picture G2.

Starting the Lawnmower

The switchbox is provided with a lock off button (H1) to prevent accidental starting.

1.Press and hold the lock off button on the

switchbox (H1), then squeeze the start/stop lever

towards the upper handle (H2).

2.Continue to squeeze the start/stop lever and release the lock off button.

ROYAL 43ELS (K)

Engage the clutch by squeezing the clutch lever towards the handle.

Adjusting the Clutch Cable - Royal 43ELS only

1.Ensure the cable is not twisted and runs freely down the handles.

2. Loosen locknut (L1) and screw adjuster (L2) “IN”, in the direction of the arrow, if clutch does not engage

when the clutch lever is pulled towards the handle.

3.Screw adjuster (L2) “OUT”, in the opposite direction from the arrow, if the clutch does not disengage when the clutch lever is free.

4.Tighten locknut (L1) finger tight then 1/4 turn with a spanner.

Stopping the Lawnmower

1. Release the pressure on the start/stop lever.

MOWING

How to Mow
1. Start mowing from the outside edge of the lawn,
mowing in strips in alternate directions	(M).

2.Mow twice a week in the growing season, your lawn will suffer if more that one third of its length is cut at one time and this may also result in poor

collection.

Please Note:-

Do not overload your Lawnmower When mowing in long thick grass a first cut with the cutting height adjusted to its highest setting, see Cutting Height, will help reduce motor overload and will help prevent damage to your lawnmower.

Cutting Height Adjustment

ROYAL 36EL

1. Height of cut is adjusted by raising or lowering the four wheels. Pull the adjustment levers away from the location slots and move them to the

selected position (N).

2.When cutting long grass the machine cutting

height should be set to its highest setting, i.e. the blade is furthest away from the grass. Adjust the height of cut to suit the condition of your lawn, for

long grass use a high cut and vice versa.

•All four wheels should be adjusted to the same height.

ROYAL 43EL/ELS

1. Height of cut is adjusted by raising or lowering

the four wheels.	Pull the adjustment lever away
from the location	slots and move it to the
selected position.		(P)

2.When cutting long grass the machine cutting

height should be set to its highest setting, i.e. the blade is furthest away from the grass.

Adjust the height of cut to suit the condition of your lawn, for long grass use a high cut and vice versa.

Grass Collection Indicator

IMPORTANT!

The machine must be switched on for the grass collection indicator to operate.

1.When the indicator is visible - grass is being collected. (Q1)

2.When the indicator drops outs of sight - it's time

to empty the grassbox. (Q2)

Grassbox Removal

1. Lift the safety flap and remove the grassbox see R.

Emptying the Grassbox

1. Hold the grassbox as illustrated when emptying.

(S)

Using as a mulcher (if applicable)

Switch off your lawnmower, wait until the blade has stopped rotating and disconnect from the mains electricity supply.

1. Lift	the safety flap. Twist and slide mulching plug
into	rear discharge chute	(T1).
2. Ensure mulching plug is securely fitted		(T2).

3.The mulching plug prevents grass from being collected by blocking the collection chute on the underside of the deck.

4.Ensure the safety flap is positioned correctly.

To Produce a Striped Effect on Your Lawn Applicable to U.K. Only (V)

1.You may find it necessary to try different cutting heights to find out which setting will achieve the best stripe on your lawn.

2.the ability of the lawnmower to produce and effective stripe will depend on the grass type and condition.

3.Cut all awkward places first before mowing the main part of your lawn in a regular up and down sequence.

ENVIRONMENTAL INFORMATION

Electrolux Outdoor Products are manufactured under an Environmental Management System (ISO 14001) using, where practical, components manufactured in the most environmentally responsible manner, according to company procedures, and with the potential for recycling at the end of the products’ life.

•Packaging is recyclable and plastic components have been labelled (where practical) for categorised recycling.

•Awareness of the environment must be

considered when disposing of ‘end-of-life’ product.

•If necessary, contact your local authority for disposal information.

ENGLISH - 3