Manuals / Husqvarna / Lawn and Garden / Tiller

Husqvarna 650RTT TO REPLACE GROUND DRIVE BELT See Fig, GROUND DRIVE BELT ADJUSTMENT See Fig

Models: 650RTT

1 28

Download 28 pages 20.99 Kb

Page 15

TO REPLACE GROUND DRIVE BELT (See Fig. 23)

SERVICE AND ADJUSTMENTS

TO REPLACE GROUND DRIVE BELT (See Fig. 23)

•Remove belt guard (See “TO REMOVE BELT GUARD” in this section of this manual).

•Remove old belt by slipping off engine pulley ﬁrst then remove from transmission pulley.

•Place new belt in groove of transmission pulley and into engine pulley. BELT MUST BE IN GROOVE ON TOP OF IDLER PULLEY. NOTE POSITION OF BELT TO GUIDES.

•Check belt adjustment as described below.

•Replace belt guard.

•Reposition wheel and replace clevis pin and hairpin clip.

GROUND DRIVE BELT ADJUSTMENT (See Fig. 23)

For proper belt tension, the extension spring should have about 5/8 inch stretch when drive control bar is in “ENGAGED” position. This tension can be attained as follows:

•Loosen cable clip screw securing the drive control cable.

•Slide cable forward for less tension and rearward for more tension until about 5/8 inch stretch is obtained while the drive control bar is engaged.

•Tighten cable clip screw securely.

CABLE CLIP SCREW

ENGINE

PULLEYDRIVE CONTROL CABLE

LESS

TENSION

		MORE
5/8"		TENSION

IDLER	EXTENSION
IDLER	SPRING
PULLEY	TRANSMISSION PULLEY
	FIG. 23

15

Image 15

Husqvarna 650RTT TO REPLACE GROUND DRIVE BELT See Fig, GROUND DRIVE BELT ADJUSTMENT See Fig, Service And Adjustments

Contents

650RTT TRAINING SAFETY RULESSafe Operation Practices for Walk-Behind Powered Rotary Tillers MAINTENANCE AND STORAGE7-10 TABLE OF CONTENTSPRODUCT SPECIFICATIONS CUSTOMER RESPONSIBILITIESOPERATOR’S POSITION See Fig ASSEMBLYTOOLS REQUIRED FOR ASSEMBLY CONTENTS OF HARDWARE PACKINSTALL HANDLE See Figs. 3, 4, and UNPACKING CARTON See FigASSEMBLY CHECK TIRE PRESSURE ATTACH CLUTCH CABLE See FigCONNECT SHIFT ROD See Fig REMOVE TILLER FROM CRATEMEETS ANSI SAFETY REQUIREMENTS OPERATIONKNOW YOUR TILLER FORWARD - WHEELS ONLY/TINES STOPPED HOW TO USE YOUR TILLERSTOPPING See Fig TINE OPERATION - WITH WHEEL DRIVECHECK ENGINE OIL LEVEL See Fig.12 BEFORE STARTING ENGINEOUTER SIDE SHIELDS See Fig TO TRANSPORTOPERATION TINE SHEAR PINSTILLING HINTS CULTIVATINGGENERAL RECOMMENDATIONS MAINTENANCEMAINTENANCE SCHEDULE LUBRICATION CHARTTO CHANGE ENGINE OIL See Figs. 16 and ENGINEAIR FILTER See Fig Do not touch hot mufﬂer or cylinder ﬁns as contact may cause burnsCOOLING SYSTEM See Fig CLEANINGMUFFLER SPARK PLUGTIRE CARE SERVICE AND ADJUSTMENTSTO ADJUST HANDLE HEIGHT See Fig TILLERGROUND DRIVE BELT ADJUSTMENT See Fig TO REPLACE GROUND DRIVE BELT See FigSERVICE AND ADJUSTMENTS TINE REPLACEMENT See Figs. 24, 25, and SERVICE AND ADJUSTMENTStine13 ENGINE TO ADJUST THROTTLE CONTROL CABLE See FigTO ADJUST CARBURETOR SERVICE AND ADJUSTMENTSENGINE OIL STORAGEOTHER FUEL SYSTEMTROUBLESHOOTING POINTS PART REPAIR PARTSHANDLE ASSEMBLY TILLER - - MODEL NUMBER 650RTT 650BRTTA, PRODUCT NUMBER 954 32PART MAINFRAME, LEFT SIDEREPAIR PARTS TILLER - - MODEL NUMBER 650RTT 650BRTTA, PRODUCT NUMBER 954 32TILLER - - MODEL NUMBER 650RTT 650BRTTA, PRODUCT NUMBER MAINFRAME, RIGHT SIDEKEY PART NO. NO. DESCRIPTION REPAIR PARTSKEY PART NO. NO. DESCRIPTION REPAIR PARTSTILLER - - MODEL NUMBER 650RTT 650BRTTA, PRODUCT NUMBER 954 TRANSMISSIONKEY PART NO. NO. DESCRIPTION TINE SHIELDREPAIR PARTS TILLER - - MODEL NUMBER 650RTT 650BRTTA, PRODUCT NUMBER 954PART TINE ASSEMBLYREPAIR PARTS TILLER - - MODEL NUMBER 650RTT 650BRTTA, PRODUCT NUMBER 954KEY PART NO. NO. DESCRIPTION DECALSREPAIR PARTS TILLER - - MODEL NUMBER 650RTT 650BRTTA, PRODUCT NUMBERSECTION 3 ITEMS NOT COVERED BY THIS WARRANTY WARRANTY STATEMENTSECTION 1 LIMITED WARRANTY SECTION 2 HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY532 18 89-00 Rev. 1 12.05.03 TR/rad