Husqvarna 96193002300 Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before per- forming any service or adjustments:

1.Be sure throttle is in STOP position.

2.Remove safety ignition key.

3.Make sure the augers and all moving

parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

The chute deflector, attached to the top of the discharge chute, is provided to direct discharging snow away from the operator. If the deflector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

•To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 22)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a shoulder/shear bolt and hex nut. Should a for- eign object or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shoulder/shear bolt and spacer. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

IMPELLER SHEAR BOLTS

The impeller is secured to the impeller shaft with two (2) capscrew/shear bolts and hex nuts. Should a foreign object or ice become lodged in the impeller, the capscrews are designed to break, preventing damage to any other com- ponents. If impeller does not turn when auger control lever

is engaged, check to see if the capscrews have sheared. 16

To replace the capscrew/shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

1/4-20	1/4-20 x 1-5/8	1/4-20 x 2
LOCKNUT	CAPSCREW /	SHOULDER /
	SHEAR BOLT	SHEAR BOLT
	IMPELLER HUB	SPACER
	IMPELLER
	SHAFT
		AUGER
		HUB
1/4-20
LOCKNUT	AUGER HUB	AUGER SHAFT

FIG. 22

TO REMOVE BELT COVER (See Fig. 23)

1.Remove two (2) screws securing belt cover to frame.

2.Remove belt cover.

•Replace belt cover by installing cover and screws and tighten securely.

	BELT
	COVER
FRAME	SCREWS

FIG. 23