To Replace Headlight Bulb, To Replace Fuse

SERVICE AND ADJUSTMENTS

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY

(REAR WHEEL ONLY)

FIG. 34

TO START ENGINE WITH A WEAK BATTERY (See Fig. 35)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 36)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT WIRE

CONNECTOR

02141

• Connect one end of the RED cable to the POSITIVE

(+) terminal of each battery(A-B), taking care not to

short against tractor chassis.

ENGINE

FIG. 36

•	Connect one end of the BLACK cable to the NEGATIVE
	(-) terminal (C) of fully charged battery.
•	Connect the other end of the BLACK cable (D) to good
	chassis ground, away from fuel tank and battery.

	02614
WEAK OR DEAD	FULLY CHARGED
BATTERY	BATTERY

FIG. 35

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engine manual.

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjustment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

CTH2036 XP specifications

The Husqvarna CTH2036 XP is a premium riding lawn mower designed for homeowners who seek an efficient and high-performance solution for maintaining their lawns. This powerful machine brings together advanced technology, robust construction, and user-friendly features to ensure an excellent mowing experience.

One of the standout features of the CTH2036 XP is its powerful 20 HP Kohler engine. This engine provides the necessary torque and reliability to handle various mowing conditions with ease. The engine is also designed for fuel efficiency, allowing users to maximize mowing time while minimizing fuel expenses.

The CTH2036 XP boasts a 36-inch cutting deck, which is perfect for maneuvering through tight spaces and achieving a clean, even cut. The deck is equipped with three high-performance blades that ensure a superior grass-cutting experience. Additionally, the cutting height can be easily adjusted, allowing users to set the desired length for their lawn seamlessly.

Another significant characteristic of the CTH2036 XP is its ergonomic design. The mower features an adjustable high-back seat that provides comfort during extended mowing sessions. The easy-to-reach controls are intuitively placed to enhance the overall user experience, making operation simple even for those new to riding lawn mowers.

Husqvarna has also integrated several innovative technologies into the CTH2036 XP. One key feature is the warranty, which offers peace of mind through its reliable performance and durability. The addition of the Easy Start system allows for effortless starting, requiring only the turn of a key to get going.

Moreover, the mower is equipped with a robust transmission system that delivers smooth acceleration and deceleration. Users can effortlessly navigate different terrains while maintaining control over the machine. An important aspect of the CTH2036 XP is its compact size, which makes it ideal for residential properties with a moderate amount of lawn space.

In conclusion, the Husqvarna CTH2036 XP is a versatile and innovative riding lawn mower that combines power, comfort, and technology to provide an exceptional mowing experience. Whether you are looking to maintain a well-manicured lawn or tackle overgrown grass, this model stands as a top choice in the realm of residential mowers. With its reliable performance and user-centric design, the CTH2036 XP is sure to impress even the most discerning homeowners.

Husqvarna CTH2036 XP To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Models: CTH2036 XP