SERVICE AND ADJUSTMENTS

TO ADJUST ATTACHMENT CLUTCH (See Fig. 24)

The electric clutch should provide years of service. The clutch has a built-in brake that stops the pulley within 5 seconds. Eventually, the internal brake will wear which may cause the mower blades to not engage, or, to not stop as required. Adjustments should be made by your nearest authorized service center/department.

Make sure attachment clutch and ignition switches are in “OFF” position.

Adjust the three nylon locknuts until space between clutch plate and rotor measures .012" at all three slot locations cut in side of brake plate.

NOTE: After installing a new electric clutch, run tractor at full throttle and engage and disengage electric clutch 10 cycles to wear in clutch plate.

BELT INSTALLATION -

Install new belt around engine pulley first, then around transaxle pulley and lastly into all the idler pulleys.

Check to be sure belt is positioned correctly and is on proper side of all belt keepers.

Engage the drive belt tension handle and replace the retainer spring.

Reinstall mower.

 

RETAINER

 

SPRING

 

DRIVE BELT TENSION

ROTOR

SLOT (3)

CLUTCH PLATE

NYLON

LOCKNUT (3)

00751

.012"

BRAKE PLATE

HANDLE

02504

 

ENGINE PULLEY

TRANSAXLE

PULLEY

BELT KEEPER

 

FLAT IDLER

 

FIG. 24

TO CHECK AND ADJUST BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.

TO CHECK BRAKE

Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and en- gage parking brake.

Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE/REPLACE PADS

Contact a qualified service center.

TO REPLACE MOTION DRIVE BELT (See Fig. 25)

Park the tractor on level surface. Engage parking brake. For ease of service there is a belt installation guide decal on bottom of left footrest.

Remove mower (See “TO REMOVE MOWER” in this section of this manual.)

BELT REMOVAL -

Create slack in belt by removing retainer spring from drive belt tension handle.

Remove belt from all idler pulleys, transaxle pulley and then from engine pulley.

 

 

BELT

BELT

2498

KEEPER

 

BELT

 

KEEPER

CLUTCHING

KEEPER CLUTCHING

V-IDLER

FLAT IDLER

 

IDLER

 

FIG. 25

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 26)

The motion control lever has been preset at the factory and adjustment should not be necessary.

Park tractor on level surface. Stop tractor by turning ignition key to “OFF” position and engage parking brake.

Loosen the adjustment bolt in front of the right rear wheel.

Move motion control lever to the neutral position (N).

Tighten the adjustment bolt.

02508

ADJUSTMENT

BOLT

FIG. 26

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See“PURGETRANSMISSION” in the Operation section of this manual.

23

Page 23
Image 23
Husqvarna GTH2554XP To Adjust Attachment Clutch See Fig, To Check and Adjust Brake, To Replace Motion Drive Belt See Fig

GTH2554XP specifications

The Husqvarna GTH2554XP is a robust and versatile riding lawn mower designed for homeowners who seek efficiency and power in their lawn care routine. This mower is equipped with a powerful 24 HP Briggs & Stratton engine that delivers excellent performance, ensuring that it can tackle even the most challenging terrains with ease. The engine is paired with a hydrostatic transmission, which allows for smooth and effortless speed adjustments without the need for manual gear shifting.

One of the standout features of the GTH2554XP is its cutting deck. The 54-inch cutting deck is designed to provide a wide cutting path, reducing the time required to mow larger areas. The deck is made from high-quality stamped steel, ensuring durability and longevity. Additionally, it comes with a cutting height adjustment feature that allows users to choose from multiple height settings, ensuring a precise cut tailored to their lawn’s needs.

The mower is also designed with comfort in mind. Its ergonomic steering wheel and adjustable seat allow the operator to maintain a comfortable posture during extended mowing sessions. The high-back seat provides excellent lumbar support, making it suitable for long hours of work. Furthermore, the mower features cruise control, enabling users to maintain a steady speed without having to keep their foot on the pedal, thus reducing fatigue.

Another impressive aspect of the Husqvarna GTH2554XP is its innovative technology integration. It is compatible with various attachment options, including mulching kits and baggers, making it a versatile choice for lawn care. The mower’s compact design makes it maneuverable around tight corners and flower beds, providing an efficient mowing experience.

Safety is also a priority with the Husqvarna GTH2554XP; it is equipped with a motion detector that automatically shuts off the engine if the operator leaves the seat. This feature adds an extra layer of safety, especially in households with children or pets.

Overall, the Husqvarna GTH2554XP combines power, comfort, and advanced features to deliver an exceptional mowing experience. Its robust build, efficient engine, and innovative technology make it an ideal choice for homeowners who value quality and performance in their lawn maintenance equipment. Whether tackling a small yard or a larger property, the GTH2554XP stands out as a reliable and efficient solution.