SERVICE AND ADJUSTMENTS

Lift seat pan to raised position.

Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

Install new battery with terminals in same position as old battery.

First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

HOOD

HEADLIGHT

WIRE

CONNECTOR

SEAT PAN

FIG. 27

TERMINAL

KEPS

NUT

COVER

 

HEX

BOLT

POSITIVE (RED)

NEGATIVE

CABLE

(BLACK) CABLE

FIG. 28

TO REPLACE HEADLIGHT BULB

Raise hood.

Pull bulb holder out of the hole in the backside of the grill.

Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 29)

Raise hood.

Unsnap headlight wire connector.

Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

To replace, reverse above procedure.

23

FIG. 29

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 30)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

Check to see if hole in throttle lever and hole in speed control bracket are aligned.

If holes are not aligned, loosen cable clamp screw and align the holes by inserting a pencil or a 1/4" drill bit through both holes.

Pull throttle cable up to remove slack and tighten cable clamp screw. Remove alignment pencil or drill bit.

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjustment should not be necessary.However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

IHigh speed stop is factory adjusted. Do not adjust - dam- age may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED.OVERSPEEDINGTHE ENGINE ABOVETHE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACTYOUR NEAREST AUTHORIZED SERVICE CENTER/ DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.

CABLE

CLAMP

SCREW

SPEED

CONTROL

BRACKET

THROTTLE LEVER

FIG. 30

Page 23
Image 23
Husqvarna LTH1742 owner manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse, To Adjust Carburetor

LTH1742 specifications

The Husqvarna LTH1742 is a standout in the realm of riding lawn mowers, designed to deliver both performance and comfort for homeowners managing medium to large lawns. With its robust build and user-friendly features, it ensures a seamless mowing experience that meets the demands of any yard.

One of the key features of the LTH1742 is its powerful engine. Equipped with a 17-horsepower Briggs and Stratton engine, this mower provides ample power to handle tough grass and uneven terrain. The reliable four-stroke engine ensures efficient fuel consumption while producing the necessary torque for effective cutting even in challenging conditions.

The 42-inch cutting deck is another significant characteristic of the Husqvarna LTH1742. Its size strikes a balance between maneuverability and mowing efficiency, allowing users to cover a wider area in less time. The deck features a robust steel construction for durability, and the cutting height can be easily adjusted from 1 to 4 inches using a convenient lever, catering to various grass types and user preferences.

To enhance the mowing experience, the LTH1742 incorporates hydrostatic transmission. This technology provides the operator with smooth and precise control over speed and direction, allowing for effortless navigation around obstacles and tight corners. The automatic drive system eliminates the need for gear shifting, making it accessible for users of all experience levels.

Comfort is also a focal point of the Husqvarna LTH1742. It comes equipped with an ergonomic seat that offers ample support, ensuring that users can mow for extended periods without discomfort. The easy-to-reach controls and intuitive dashboard further enhance user experience, allowing for quick adjustments without needing to divert attention from the mowing process.

Another notable feature includes the ease of maintenance. The mower is designed with a washout port that makes cleaning the cutting deck a straightforward task, prolonging the equipment's lifespan and maintaining optimal performance. Additionally, the LTH1742 offers a variety of accessories, enabling users to customize their mower for different tasks, such as mulching or bagging.

In summary, the Husqvarna LTH1742 combines power, efficiency, and user-friendly features, making it an excellent choice for homeowners looking to maintain their lawns with ease. Its powerful engine, adjustable cutting deck, hydrostatic transmission, and attention to operator comfort solidify its place as a reliable and effective lawn care solution.