Meets A.N.S.I. Safety Requirements | Husqvarna ST 330T guide

OPERATION

MUFFLER

CHOKE CONTROL

THROTTLE

CONTROL

ON/OFF

SWITCH

		AUGER	DRIVE SPEED
	POWER CORD	CONTROL	CONTROL LEVER	DEFLECTOR
	POWER CORD	LEVER	CONTROL LEVER	DEFLECTOR
GASOLINE	PLUG	LEVER		REMOTE
GASOLINE	PLUG			REMOTE
FILLER CAP			CONTROL LEVER
	ELECTRIC	DISCHARGE
	START	CHUTE
	BUTTON	CONTROL
		LEVER

LIGHT

PRIMER	TOOLBOX
PRIMER
SAFETY IGNITION	CHUTE
KEY	CHUTE
FUEL SHUT-OFF VALVE	DEFLECTOR
FUEL SHUT-OFF VALVE
RECOIL STARTER HANDLE	DISCHARGE
	DISCHARGE
	CHUTE
NOTE: ITEMS ABOVE	CLEAN-OUT TOOL
ARE SHOWN IN	CLEAN-OUT TOOL
THEIR TYPICAL
LOCATION ON THE
ENGINE. ACTUAL
LOCATION MAY VARY
WITH THE ENGINE
ON YOUR UNIT.

LH TURN

TRIGGER

TRACTION DRIVE CONTROL LEVER

HANDLE

KNOB

MUFFLER

AUGERS

FIG. 10

DRIFT

CUTTER

SKID PLATE

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button – used for starting the engine.

Recoil (auxiliary) starter handle – used for starting the engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

Choke control - used for starting a cold engine. ON / OFF switch - used to STOP the engine.

Throttle- used to select FAST or SLOW engine speeds. 9

Drive speed control lever - used to select forward or reverse motion and speed of snow thrower.

Traction drive control lever - used to engage power- propelled forward or reverse motion of snow thrower.

LH and RH turn triggers - used to steer the snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control lever - used to change the di- rection the snow is thrown.

Skid plate - used to adjust height of scraper bar from the ground.

Drift cutter - used to cut through deep snowdrifts.

Image 9

Husqvarna ST 330T warranty Meets A.N.S.I. Safety Requirements, Recoil auxiliary starter handle used for starting the engine

Contents

Operator’s Manual Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Skid Plates Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper Handle Install Auger Control ROD See Figs Install Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Know Your Snow Thrower Operation Recoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety Requirements SET Height Adjustment See Figs Transport and Height Adjustment of Snow ThrowerTo Transport See Figs Packed Snow Normal Operation Transport Float Stopping HOW to USE Your Snow Thrower Using the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig To Transport Before Starting the Engine To Start Engine ADD Gasoline See FigCold Start Electric Starter Warm Start Electric Starter Warm Start Recoil Starter Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE Lubrication Engine Cleaning To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Adjust Traction Belt and Auger Belt Tension To Adjust Cable Tension See FigTo Remove Tracks See Fig Carburetor Instructions for Adjusting Power Steering Cables See Figs Other StorageFuel System Engine OIL Problem Cause Correction Troubleshooting Consumer Wheeled Products Limited Warranty HOW to Obtain Service Consumer Wheeled Limited Warranty Chart Armor Protected Stamped Deck Shell Example Below 06/17/2014 TH