IBM PCM-5896 - page 18

6PCM-5896 User Manual

Expansion Slots

• PC/104 connector: One 16-bit 104-pin connector onboard

• PCI slot: One 32-bit PCI slot onboard

Mechanical and Environmental

• Power supply voltage: +5V (4.75V to 5.25V),

+12V (11.4V to 12.6V)

• Typical power requirement: +5V@8A

• Operating temperature: 32 to 140o F (0 to 60o C)

• Board size: 8"(L) x 5.75"(W) (203mm x 146mm)

• Weight: 1.2 lb. (0.5 Kg)

Contents

Main Page Copyright Notice Acknowledgements A Message to the Customer EMAC Customer Services Technical Support Product Warranty Packing list Notice Contents Page Page Page Page Page Introduction Highly integrated multi-media SBC Features Specifications Page Page Page 8PCM-5896 User Manual Board dimensions dimensions in mm PCM-5896 dimensions Installation Jumpers and connectors Page Locating jumpers Locating connectors Setting jumpers CPU installing and upgrading Installing DRAM (DIMMs) System Memory Supplementary information about DIMM Memory Installation Procedures Clear CMOS (J2) DOC address select (J3) ATX Soft-Power Switch connector (J4) COM2 RS-232/422/485 select (J6, J11) LCD driving voltage select (J8) LCD clock signal select (J7) COM3/COM4 RI pin voltage select (J10, J5) *default Audio output select (J12) S1 (2~6) CPU Vcore select 1 : ON 0 : OFF * default S3 (1~3) CPU clock select S3 (4~6) CPU frequency ratio Power connectors (CN8, CN1) ATX power connector (CN8) The ATX power supply uses 20-pin connector shown below. Make sure you plug in the right direction. CPU fan power connector (CN1) Plug in the fan cable to the 3-pin fan connector onboard. The fan connector is marked CN1. USB connector (CN3) IDE hard drive connector (CN5) Connecting the hard drive IDE hard drive connector (CN5) Front panel connector (CN6) Speaker LED interface IrDA connector (CN7) Display connectors (CN9, CN12) VGA display connector (CN12) LCD connector (CN9) CD Audio connector (CN10) Keyboard and mouse connector (CN11) Audio connector (CN13) Parallel port connector (CN14) Parallel port IRQ Parallel port connector table (CN14) 100Base-Tx Ethernet connector (CN15) Serial ports (CN16) COM 1-4 RS-232/422/485 serial ports (CN16) Floppy drive connector (CN17) Connecting the floppy drive Chapter 2 Installation 39 Floppy drive connector (CN17) Floppy drive connector (CN17) Pin Signal Pin Signal Ethernet LED signal connectors (LED1) Ethernet active signal LED Ethernet link signal LED DiskOnChip socket (U23) DiskOnChip (DOC) 2000 Installation Configure DOC as a boot device Page Starting setup Setup keys These keys helps you navigate in Setup: Getting help In Case of Problems Main setup Menu Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page ENTER PASSWORD: CONFIRM PASSWORD: Page Page Page Page Page Software drivers Hardware configuration Necessary prerequisites Before you begin Windows 95 Driver installation Page Page Page Page Page Page Page Windows 3.1 OS/2 Page Windows NT 3.51 Windows NT 4.0 Page Ethernet software configuration Page Introduction Setting Up in Windows 95 Installing the Drivers and the Application Page Setting Up in NT4.0 Page A Programming the watchdog timer How to program the WATCHDOG TIMER Demo program Page Page Installing PC/104 modules PC/104 Module Mounting Diagram PC/104 module dimenstions (inches 5%) Page Page 114 PCM-5896 User Manual PCM-10489-4 Wiring Kit The cable kit PCM-10489-4 includes the following cables: