Icom IC-F3022S, IC-F3023S, IC-F3022T Adjustment Procedures, Before Starting Software Adjustment

SECTION 6 ADJUSTMENT PROCEDURES

6-1 PREPARATION

When adjusting IC-F3020 series, CS-F3020 CLONING SOFTWARE, CS-F3020 ADJ ADJUSTMENT SOFTWARE (Rev. 1.0 or later), OPC-478/U JIG CABLE (modified OPC-478/U CLONING CABLE; see the page 6-2) and the following test equipments are required.

EQUIPMENT	GRADE AND RANGE		EQUIPMENT	GRADE AND RANGE
DC power supply	Output voltage	: 7.2 V DC	External speaker	Input impedance	: 8 Ω
	Current capacity	: More than 1.5 A		Capacity	: 1 W or more
FM deviation meter	Frequency range	: DC–300 MHz	Attenuator	Power attenuation	: 20 or 30 dB
	Measuring range	: 0 to ±10 kHz		Capacity	: 7.5 W
	Frequency range	: 0.1–300 MHz	Standard signal	Frequency range	: 0.1–300 MHz
Frequency counter	Frequency accuracy	: ±1 ppm or better			: 0.1 µV to 32 mV
			generator (SSG)	Output level
	Sensitivity	: 100 mV or better			(–127 to –17 dBm)
	Measuring range	: 0.1–7.5 W
RF power meter	Frequency range	: 100–300 MHz	Oscilloscope	Frequency rang	: DC–20 MHz
	Impedance	: 50 Ω		Measuring range	: 0.01–20 V
	SWR	: Better than 1.2 : 1

▄SYSTEM REQUIREMENTS (for the ADJUSTMENT SOFTWARE)

• Microsoft® Windows® 98/98SE/Me/2000/XP • RS-232C serial port (D-sub 9 pin) or USB port

▄ADJUSTMENT SOFTWARE INSTALLATION q Quit all applications when Windows is running. w Insert the CD into the appropriate CD drive.

e Double-click the “Setup.exe” contained in the ‘CS-F3020 ADJ’ folder in the CD drive.

r The “Welcome to the InstallShield Wizard for CS-F3020 ADJ” will appear. Click [Next>].

t The “Choose Destination Location” will appear. Then click [Next>] to install the software to the destination folder. (e.g. C:\Program Files\Icom\CS-F3020 ADJ)

y After the installation is completed, the “InstallShield Wiz- ard Complete” will appear. Then click [Finish].

u Eject the CD.

i Program group ‘CS-F3020 ADJ’ appears in the ‘Programs’ folder of the start menu, and ‘CS-F3020 ADJ’ icon ap- pears on the desk top screen.

▄BEFORE STARTING SOFTWARE ADJUSTMENT

Clone the adjustment frequencies and settings into the transceiver, and set the configuration using the CS-F3020 CLONING SOFTWARE before starting the software adjustment. Otherwise, the software adjustment can not be started.

CAUTION!: BACK UP the originally programmed memory data in the transceiver before programming the adjustment frequencies. When program the ad- justment frequencies into the transceiver, the transceiver’s memory data will be overwritten and lose original memory data at the same time.

Microsoft and Windows are registered trademarks of Micro- soft Corporation in the U.S.A. and other countries.

▄STARTING SOFTWARE ADJUSTMENT

qConnect the transceiver and PC with OPC-478/U JIG

CABLE.

wTurn the transceiver power ON.

eBoot up Windows, and click the program group ‘CS-F3020

ADJ’ in the ‘Programs’ folder of the [Start] menu, then CS-F3020 ADJ’s window appears.

rClick ‘Connect’ on the CS-F3020 ADJ’s window, then the

window shows transceiver’s condition and adjustment items as below.

tSet or modify adjustment data as specified.

• ADJUSTMENT FREQUENCY LIST

CH	FREQUENCY	ADJUSTMENT ITEM
1	174.000 MHz	TX power	: Low1
		Mode	: Narrow
2	136.000 MHz	TX power	: Low1
		Mode	: Wide
3	155.000 MHz	TX power	: High
		Mode	: Wide
4	155.000 MHz	TX power	: Low2
		Mode	: Wide
5	155.000 MHz	TX power	: Low1
		Mode	: Narrow
		TX power	: Low1
6	155.000 MHz	Mode	: Narrow
		DTCS	: 007
7*	155.000 MHz	TX power	: Low1
		Mode	: Middle
		TX power	: Low1
8	155.000 MHz	Mode	: Wide
		CTCSS	: 151.4 Hz
9	155.000 MHz	TX power	: Low1
		Mode	: Wide

*; [EUR] only

6 - 1