| ADJUSTMENT | ADJUSTMENT CONDITIONS |
| MEASUREMENT | VALUE | ADJUSTMENT | |||||
|
|
|
|
|
|
| |||||
UNIT |
| LOCATION | UNIT | ADJUST | |||||||
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
| IDLING | 1 | • Operating frequency | : 12.2350 MHz | Rear |
| Connect | an ammeter | 2.0 A | PA | R6304 |
| CURRENT |
| • Mode | : J3E | panel |
| (10 A) | between an |
|
|
|
| (For drive |
| • Apply no audio signal to the [MICRO- |
|
| external power supply |
|
|
| ||
| FETs) |
| PHONE] connector. |
|
|
| and the transceiver. |
|
|
| |
|
|
| • Disconnect J6702. |
|
|
|
|
|
|
|
|
|
|
| • Preset R6304 and R6412 on the PA |
|
|
|
|
|
|
| |
|
|
| unit to max. counter clockwise. |
|
|
|
|
|
|
| |
|
|
| • Connect a dummy load or RF power |
|
|
|
|
|
|
| |
|
|
| meter to the [ANT] connector. |
|
|
|
|
|
|
| |
|
|
| • Transmitting |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| (For final | 2 | • Transmitting |
|
|
|
|
| 0.7 A |
| R6412 |
| transistors) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
| • After adjustment, connect J6701 to the PA unit. |
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
| |
| SWR | 1 | • Operating frequency | : 22.0000 MHz | Rear |
| Connect an RF power | 140 W | Audio | Output | |
| DETECTOR |
| • Mode | : J3E | panel |
| meter to the [ANT] |
| gen- | level | |
|
|
| • Connect the CP7332 (FOR line) on |
|
| connector. |
| erator |
| ||
|
|
| the FILTER unit to ground. |
|
|
|
|
|
|
| |
|
| 2 |
|
|
|
|
|
|
| ||
|
| • Connect an audio generator to the | FIL- |
| Connect a DC volt- | Minimum level | FIL- | C7275 | |||
|
|
| [MICROPHONE] connector and set | TER |
| meter to check point, |
| TER |
| ||
|
|
| as: |
|
|
| CP7331. |
|
|
|
|
|
|
| Frequency | : 1.5 kHz |
|
|
|
|
|
|
|
|
|
| • Transmitting |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
| • After adjustment, disconnect CP7332 (FOR line) on the FILTER unit from ground. |
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
4 - 5