Ikelite Digital Housing

i n s t r u c t i o n m a n u a l

#6114.05 for Sony DSC-W5 & W7 Cameras

Congratulations on your purchase of an Ikelite Digital Camera Housing. Ikelite has over 40 years of experience in the underwater photographic and lighting market. Our products are designed and built in the USA by Ikelite for both the professional and amateur photographer.

The clear housing permits instant visual inspection of the camera and all sealing surfaces as well as complete monitoring of controls and camera LCD screens.

Ikelite Digital Housings are slightly negative in salt water for stability. This housing has been water pressure tested at the factory. Housing is pressure tested to 200’ (60m).

Opening the Housing

 

1. Lid Snaps have a Lock.

 

Push Forward

To open, push Lid Snap Lock

Lid Snap Lock

forward and lift as shown.

 

Keep pressure on the Lid

 

Snap so it does not fly open

 

quickly.

 

Lift

Some lid snaps have a lot of

 

spring tension once they go over center, have a firm grip on the

lid snap. Lid Snaps may be opened one at a time.

Installing the Camera

 

 

Remove the back

 

 

from the housing.

 

 

The mounting tray

O' Ring

 

for the camera is

 

 

secured to the

Lid

 

housing back.

Hook

 

Position the camera

 

 

on the tray and

 

 

secure it with the

 

 

mounting bolt which

 

 

threads into the

Tray

Mounting Bolt

camera’s tripod

 

CAMERA / MOUNT

 

Mounting

socket.

CAUTION:

Some camera tripod socket threads are plastic. The mounting tray bolt is metal. Do not cross thread or over tighten as you may damage the camera tripod socket threads.

4

Power

Shutter

Release

Lid

 

 

 

 

Lens

 

 

 

 

Lid

 

 

 

 

 

 

 

 

Snap

 

 

 

 

Port

 

 

 

 

Snap

 

 

 

 

 

 

 

 

 

 

 

Front View

Zoom

Mode

Thumb

Rest

 

 

 

 

Display

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Menu

 

 

 

 

 

 

 

 

 

 

 

 

Lanyard

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Delete

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Control

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Back View

 

 

 

 

Button

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Closing the Housing

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.

Place housing face down in your

 

 

 

 

 

 

 

 

housing back

 

 

 

 

 

 

 

 

 

 

 

 

lap or on flat surface.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.

Check to see that there is an

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

o’ring on the housing back and

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

that it is clean and in its proper

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

location.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Guide the back onto the housing.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The o’ring should touch the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

o’ring

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

housing all the way around. There

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

should be an even gap all the way

housing

 

 

 

 

 

 

 

 

 

 

around between the housing and

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4.

the housing back.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Lift the lid snaps so they are

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

extended and place the lid snap

 

 

 

 

 

 

 

 

housing back

 

 

 

 

 

 

 

 

 

 

 

 

 

 

into the hook on the housing

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

back.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5.

To close the housing push

even gap

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

down on the lid snaps until

all 4 sides

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

they snap into place . Lid

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

snaps on opposite sides of the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

o’ring

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

housing should be closed at the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

same time. Be sure they are down

housing

 

 

 

 

 

 

 

 

 

 

far enough to engage the lock.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Double check - Once the housing is closed, check the o’ring seal. Check the gap between the housing back and the housing, it should be even all the way around.

Look through the clear plastic back at the o’ring. You should see a darkened area where the o’ring is compressed against the housing back. If you do not see an even black compression seal all the way around the back, open the lid snaps, reseat the housing back and close the lid snaps. Visually check the seal again.

5

Page 2
Image 2
Ikelite DSC-W7, DSC-W5 instruction manual Opening the Housing, Closing the Housing, Installing the Camera

DSC-W7, DSC-W5 specifications

The Ikelite DSC-W5 and DSC-W7 are well-regarded underwater camera housings designed specifically for the Sony Cyber-shot series, particularly the DSC-W5 and DSC-W7 models. These housings allow photographers to explore underwater environments while effectively protecting their cameras from water damage.

One of the standout features of the Ikelite housings is their robust construction. Made from durable materials, the housings ensure excellent performance and longevity in challenging underwater conditions. The clear polycarbonate design allows users to easily monitor camera controls and view the camera's LCD screen while diving.

Both the DSC-W5 and DSC-W7 models are equipped with high-resolution sensors, enabling sharp and vibrant image capture. The Ikelite housings maximize the potential of these sensors by offering precise controls that allow users to adjust settings without removing the camera from the housing. This feature is particularly valuable for underwater photography, where lighting conditions can vary dramatically.

The Ikelite housings also include user-friendly controls that align with the camera's buttons, allowing photographers to utilize functions such as zoom and settings adjustments with ease. Additionally, the housings feature an array of threaded ports, accommodating various accessories such as external strobes and wide-angle lenses, further enhancing the creative possibilities for photographers.

One of the critical technologies integrated into the Ikelite DSC-W5 and DSC-W7 housings is a waterproof rating. These housings are typically rated to depths of up to 200 feet, making them suitable for both novice and experienced divers. This depth rating, paired with the camera's built-in image stabilization, provides a solid foundation for capturing stunning underwater scenes, even in challenging conditions.

Furthermore, the Ikelite housing design ensures easy access to the camera's battery and memory card without needing to remove it from the housing, minimizing interruptions during dives. The ergonomic design of the housing makes it comfortable to hold, even while wearing gloves.

In conclusion, the Ikelite DSC-W5 and DSC-W7 underwater housings are essential tools for enthusiasts looking to capture stunning underwater photography. Their robust construction, user-friendly controls, waterproof capabilities, and accessory compatibility make them a favorite among divers and photographers alike. With these robust housings, users can unlock the full potential of their Sony Cyber-shot cameras and capture the beauty of the underwater world with confidence.