4
EN

Where to install the tumble dryer

 Install the dryer far from gas
ranges, stoves, radiators or
hobs, as flames may damage it.
If the dryer is installed below a
worktop, ensure there are 10
mm between the upper panel of
the dryer and any objects
above it, and 15 mm between
the sides of the machine and
the walls or furniture units
adjacent to it. This ensures
adequate air circulation.

Ventilation

 The room must be adequately ventilated while the dryer is
running. Make sure that the dryer is installed in a room free of
humidity and with adequate air circulation. The flow of air
around the dryer is essential to allow water to condense
during drying; the dryer will not function properly if it is placed
in an enclosed space or inside a cabinet.
Some condensation may form if the dryer is used in a small
or cold room.
We do not recommend that the dryer is installed in a
cupboard but the dryer must never be installed behind a
lockable door, a sliding door or a door with a hinge on the
opposite side to that of the dryer door.
Water drain
If your dryer is installed next to a drain the water can be
plumbed into this drain. This does away with the need to
empty the water container. If the dryer is stacked onto or
installed next to a washing machine it can share the same
drain. The height of the drain must be less than 3' (1 m)
from the bottom of the dryer.
Remove existing hose from position shown in picture A
and fit a suitable length of hose and connect as shown
in picture B.
Make sure that the hose is not squashed or kinked
when the dryer is in its final location.
1
0
m
m
15 mm
15mm
15 mm
15mm

Electrical connections

Before plugging the appliance into the socket, check the following:
 Make sure your hands are dry.
 The socket must have an earth connection.
 The socket must be able to withstand the machines
maximum power output as indicated on the data plate (see
Description of the tumble dryer).
 The power supply voltage must fall within the values indicated
on the data plate (see Description of the tumble dryer).
 The socket must be compatible with the dryers plug.
Should this not be the case, replace the plug or the socket.
Do not use extension cords.
The dryer must not be installed outdoors, even if the space is
sheltered. It can be very dangerous if exposed to rain or storms.
Once installed, the dryers electrical wire and plug must
be within reach.
The power cord must not be bent or squashed.
The power cord is supplied fitted with a BS1363 plug
and with a 13 amp BS1362 fuse. If it is necessary to fit a
replacement fuse, it must be a 13 Amp ASTA approved
to BS1362 type. WARNING: The plug must not be used
without a fuse cover. If a replacement fuse holder/cover is
required, it must be of the same colour coding or wording as
shown on the base of the plug.
Replacements are available from authorised dealers.
Changing the plug
The wires in the power cord are coloured in accordance
with the following.
If the plug being replaced is a non-rewirable type, then the
cut-off plug must be disposed of safely. DO NOT leave it where
it can be inserted into a socket and create a shock hazard.
The power cord should be checked periodically and replaced
by a cord specially prepared for this dryer and fitted only by
authorized technicians (see Service). New or longer power
cords are supplied at an extra charge by authorized dealers.
The manufacturer denies any responsibility should any
of these rules not be followed.
If in doubt about any of the above consult a qualified electrician.

Preliminary information

Once the tumble dryer is installed, clean the inside of the drum before
operating it and remove any dirt accumulated during transportation.
1
2
2
1
Less than 1m
Picture APicture B
Installation
GREEN &
YELLOW
BROWN
BLUE
13 ampere fuse
CROSS-BAR
CORD GRIP
Moulded plug
Green and Yellow (Earth)
wire to terminal marked
E, symbol x, or coloured
green and yellow.
Blue (Neutral) wire to
terminal marked N or
coloured black.
13A ASTA approved fuse
to BS 1362.
Brown (live) wire to teminal
marked L or coloured
red.