Gas Connection

GB

The cooktop should be connected to the gas supply by an authorized installer. During installation of this product it is essential to fit an approved gas tap to isolate the supply from the appliance for the convenience of any subsequent removal or servicing. Connection of the appliance to the gas mains or liquid gas tanks must be carried out according to the safety standards currently in force, and only after it is ascertained that it is suitable for the type of gas to be used. If not, follow the instructions indicated in the section entitled, “Adapting the Cooktop for Different Types of Gas”. If the cooktop is to be connected to tanks containing liquid gas, use pressure regulators that comply with current safety standards.

￿To insure that the appliance operates safety, the gas is regulated correctly and your appliance lasts over time, make sure that gas pressure levels comply with the indications given in Table 1, “Nozzle and Burner Specifications”.

Gas Connection to Non-flexible Pipe (copper or steel)

￿Connection to the gas source must be done in such a way as to not create any stress points at any part of the appliance.

The appliance is fitted with an adjustable, "L" shaped connector and a gasket for the attachment to the gas supply. Should this connector have to be turned, the gasket must be replaced (supplied with the appliance).

The gas feed connector to the appliance is a threaded, male 1/2" connector for round gas pipe.

Gas Connection to Flexible Steel Pipe

The gas feed connector to the appliance is a threaded, male 1/2" connector for round gas pipe. Only use pipes, tubes and gaskets that comply with current safety codes. The maximum length of the flexible pipes must not exceed 2000 mm. Once the connection has been made, ensure that the flexible metal tube does not touch any moving parts and is not crushed.

Check the Seal

￿Once the appliance has been installed, make sure all the connections are properly sealed, using a soapy water solution. Never use a flame.

Adapting the Cooktop for Different Types of Gas

To adapt the cooktop to a different type of gas than that for which it was designed, (see the sticker under the hob or on the packaging), the burner nozzles must be changed, as follows:

1.Remove the pan supports and slide the burners out of the cooktop.

2.Unscrew the nozzles using a 7mm socket wrench and replace them with those for the new type of gas. (See table 1, “Burner and Nozzle Specifications”).

3.Reassemble the parts following the instructions in reverse order.

4.On completing the operation, replace the old rating label with the one showing the new type of gas; the sticker is available from our Service Centres.

•Regulation of Air Supply to the Burner

The burners do not need a primary air regulator.

•Minimum Regulation

1.Turn the gas valve to minimum.

2.Remove the knob and turn the regulator

screw (positioned either on the side of the top or inside the shaft) clockwise until the flame becomes small but regular.

3.Make sure that, when the knob is turned rapidly high to low, the flame does not go out.

4.In the event of a malfunction on appliances with the security device (thermocouple) when the gas supply is set at minimum, increase the minimum supply levels using the regulator screw.

￿In the case of liquid gas, the regulation screw must be fully screwed in (clockwise).

￿Once the adjustment has been made, apply sealing wax, or a suitable substitute, to the old seals on the by-pass.

4

Page 3 Page 5
Page 4
Image 4
Indesit PI 640 A GB manual Gas Connection
Page 3 Page 5

PI 640 A GB specifications

Indesit has established itself as a reputable brand in the realm of home appliances. Among its notable offerings is the Indesit PI 640 A GB, a versatile and efficient built-in gas hob designed for modern kitchens.

One of the standout features of the Indesit PI 640 A GB is its sleek and stylish design. The hob boasts a stainless steel finish, which not only enhances the aesthetic appeal of the kitchen but also ensures durability and ease of cleaning. The four burners offer a range of cooking options, catering to various culinary needs. With different sizes, the burners allow users to simmer delicate sauces or boil large pots of water with impressive efficiency.

The Indesit PI 640 A GB is equipped with high-efficiency burners that optimize gas consumption, ensuring that cooking is both economical and environmentally friendly. These burners are designed to deliver an excellent performance, achieving high temperatures quickly while maintaining a consistent heat distribution, which is critical for even cooking results.

Safety is a paramount concern for any kitchen appliance, and the Indesit PI 640 A GB does not disappoint in this regard. It is fitted with a flame failure device that automatically shuts off the gas supply if any flame goes out. This feature provides peace of mind to users, knowing that they are cooking in a safe environment.

Another significant technology featured in this hob is the easy-to-use ignition system, which allows users to light the burners with a simple twist and push of the control knobs. The knobs are ergonomically designed for ease of use, even when wearing oven mitts or when hands are wet.

Cleaning the Indesit PI 640 A GB is hassle-free thanks to its removable burner caps and enamel grates. The smooth surface provides a quick wipe-down capability, making kitchen maintenance less of a chore.

In summary, the Indesit PI 640 A GB stands out for its combination of practicality, safety, and aesthetic appeal. Its efficient burner system, safety features, and easy maintenance make it an excellent choice for home cooks. Whether you're a novice or a seasoned chef, this gas hob is designed to deliver a reliable cooking experience that meets modern culinary demands.
Top Page Image Contents