OPERATOR’S MANUAL

651747-X-B

 

 

INCLUDING: OPERATION, INSTALLATION & MAINTENANCE

STAINLESS STEEL FLUID HEATER

RELEASED: 6-28-92

REVISED: 7-16-01 (REV. G)

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.

FLUID HEATER DATA

Models . . . . . . . . . . . . . . . . . . . . . . . . . 651747￿X￿B Wetted Parts Material . . . . . . . . . . . . . . Stainless Steel

Volts AC 651747￿1￿B . . . . . . . . . . . . 120 651747￿2￿B . . . . . . . . . . . . 230 / 240 651747￿3￿B . . . . . . . . . . . . 415 / 440

Amperes 651747￿1￿B . . . . . . . . . . . . 16.6 651747￿2￿B . . . . . . . . . . . . 8.3 651747￿3￿B . . . . . . . . . . . . 4.5

Watts . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000

Accuracy . . . . . . . . . . . . . . . . . . . . . . . . ± 3￿1/2_ F (1.9_ C) Temperature Rise Above Ambient . . . . . 100_ F (38_ C) Recovery Rate per Hour . . . . . . . . . . . . 15 gallons (56.8 liters) Maximum Working Pressure . . . . . . . . . 5000 p.s.i. (35 MPa) Maximum Temperature Range . . . . . . . 60 ￿ 250_ F (16 ￿ 121_ C) Surface Temperature Code . . . . . . . . . . T3 (392_ F / 200 _ C) Fluid Passage Diameter . . . . . . . . . . . . 0.370" (9.4 mm)

Fluid Passage Length . . . . . . . . . . . . . . 91.7" (232.9 cm) Fluid Passage Volume . . . . . . . . . . . . . . 9.86 in.3 (0.162 lit.) Inlet / Outlet Port Size (female) . . . . . . . 1/2 ￿ 14 N.P.T.F. ￿ 1 Weight . . . . . . . . . . . . . . . . . . . . . . . . . . 18 lbs (8.2 kg)

GENERAL DESCRIPTION

The Aro stainless steel fluid heater models are wired for 120, 230 / 240 and 415 / 440 volt AC applications. The heating element is a 2000 watt cartridge type and is thermostatically controlled. The wiring, heating element and thermostat are protected by a preset heat limiter.

The thermostat is adjustable up to 250_ F (121_ C). The heater is off when the thermostat knob is turned counterclockwise as far as pos￿ sible. The heater will not switch on until the knob is rotated to at least ambient room temperature.

Fluid heaters have been tested in a water solution. Some of this fluid may be left within the heater, therefore flush out this fluid with a solvent compatible with the material to be pumped.

This unit utilizes an explosion￿proof electrical section and internally spiraling material section. The material enters the base under line pressure from the pump and is heated and delivered thru to the ma￿ terial outlet at the top.

This unit is CSA certified for Class I, Division 1, Group D, Hazard￿ ous Locations, Temperature Code (identification number) T3.

Two or more paint heaters may be coupled together by plumbing the material outlet of the first heater to the material inlet of the next, etc. However, the distance of piping run between the units should be limited to no more than three feet (see figure 4, page 4).

TYPICAL INSTALLATION

The heater inlet and outlet should be plumbed (up flow) as shown (see figure 4, page 4), to minimize chances of trapped air inside the heater. If the inlet and outlet are reversed (down flow), the temperature rise will be different.

INGERSOLL-RAND COMPANY

P.O. BOX 151 D ONE ARO CENTER D BRYAN, OHIO 43506￿0151

& (419) 636-4242 D FAX (419) 633-1674 E2001 D PRINTED IN U.S.A.

DIMENSIONAL DATA

651747/X/B FLUID HEATER

 

 

7/1/2"

 

 

(190.5 mm)

7/8" (22.2 mm)

 

 

 

4/3/4"

4/3/16"

1/2 / 14 N.P.T.F.

(120.7 mm)

(105.6 mm)

Mounting holes (hidden)

 

 

Thermometer - Do not over/

 

 

tighten. For orientation only.

 

 

1/2 / 14 N.P.T.F. (Outlet)

 

16/1/16"

 

 

(408.0 mm)

 

3/3/4"

 

 

(95.3 mm)

 

8/13/16"

 

 

(223.8 mm)

 

 

R

1/2 / 14 N.P.T.F. (Inlet)

 

 

FIGURE 1

 

OPERATING PRECAUTIONS

Heed all warnings.

WARNING Do not exceed 5000 p.s.i. (35 MPa) maximum.

WARNING HIGH PRESSURE DEVICE. Improper usage of this equipment could result in serious injury. The possibility of injection into the flesh is a potential hazard. Never allow any part of the human body to come in front of, or in direct contact with, the material outlet. An injection injury can be serious. If injection should occur, contact a qualified physician for imme/ diate treatment.

CAUTION Electrical supply power to the heater must be off during flushing operation.

CAUTION Use only genuine Aro replacement parts to as/ sure compatible pressure rating and longest service life.

Page 1
Image 1
Ingersoll-Rand 651747-X-B manual Fluid Heater Data, General Description, Typical Installation, Dimensional Data

651747-X-B specifications

The Ingersoll-Rand 651747-X-B is a robust and highly efficient air compressor designed for various industrial applications. Known for its reliability and performance, this model stands out due to its advanced technologies and user-friendly features.

One of the key features of the Ingersoll-Rand 651747-X-B is its powerful, electric-driven compressor system. This ensures consistent airflow and pressure, making it ideal for demanding tasks in construction, automotive, and manufacturing sectors. The compressor is engineered to deliver optimal performance while minimizing energy consumption, which not only reduces operating costs but also enhances sustainability.

The 651747-X-B is equipped with a durable and high-quality construction that withstands the rigors of everyday use. Its heavy-duty components are designed to endure tough working conditions, providing extended service life and reducing the frequency of maintenance needs. This model's robust design is complemented by an efficient cooling system, which prevents overheating and ensures the compressor operates at peak efficiency.

Another notable characteristic of the Ingersoll-Rand 651747-X-B is its advanced control technology. The compressor features a user-friendly interface that allows operators to easily monitor and adjust settings in real time, promoting operational efficiency and safety. This technology enables automatic start-stop operations, which further conserves energy and enhances user convenience.

Moreover, the 651747-X-B incorporates noise-reducing technologies to operate quietly, making it suitable for environments where noise levels need to be kept to a minimum. The sound insulation features help create a more pleasant work atmosphere while complying with regulatory noise standards.

Maintenance is simplified with the Ingersoll-Rand 651747-X-B. Its design includes easy access to key components, making routine checks and servicing straightforward. This feature is vital for businesses aiming to minimize downtime and maximize productivity.

In summary, the Ingersoll-Rand 651747-X-B is a highly efficient air compressor that combines durability, performance, and user-friendly technology. With its robust construction, advanced control systems, energy-efficient operations, and lower noise levels, it is an excellent choice for various demanding industrial applications, ensuring reliability and integrity in every operation.