Insignia NS-19LD120A13 - page 48

44
NS-19LD120A13 Insignia 19" LCD TV/DVD Combo
www.insigniaproducts.com
Remote control
General
No output from one of the
speakers. • Adjust the audio balance. See “Adjusting sound
settings” on page25.
• Make sure that the audio cables are connected
correctly and securely to your TV/DVD combo.
After images appear. • Do not display a still image, such as a logo,
game, or computer image, for an extended
period of time. This can cause a permanent
after-image to be burned into the screen. This
type of damage is not covered by your warranty.
Problem Solution
Remote control does not
work. • Make sure that the power cord is correctly
connected to your TV/DVD combo and a power
outlet.
• Make sure that there are no obstructions
between the remote control and the remote
control sensor on the front of the TV/DVD
combo.
• Point the remote control directly at the remote
control sensor on your TV/DVD combo. For the
location of the remote control sensor, see
“Aiming the remote c ontrol” on page 18.
• The supplied batteries are wrapped tightly in
clear plastic. Make sure that you have removed
this plastic from the batteries.
• Make sure that the batteries are installed
correctly. See “Installing remote control
batteries” on page18.
• Replace dead batteries with new batteries. See
“Installing remote control batteries” on page18.
Trouble programming your
existing universal remote
control.
• See instructions and a table of common codes in
“Programming a different universal remote
control” on page47.
• Codes are subject to change. For up-to-date
codes, go to
www.insigniaproducts.com/remotecodes
• Replace dead batteries with new batteries. See
“Installing remote control batteries” on page18.
• Refer to the User Guide that accompanied your
universal remote control and contact the
manufacturer if problems persist.
Problem Solution
No power. • Make sure that the power cord is correctly
connected to your TV/DVD combo and a power
outlet.
• Unplug the power cord, wait 60 seconds, then
plug the cord back in and turn on your TV/DVD
combo.
• Other devices (for example, a surround sound
receiver, external speakers, fans, or hair dryers)
may be interfe ring wi th your TV/DVD combo. Tr y
turning off one device at a time to determine
which device is causing interference. After you
have determined which device is causing
interference, move it further from the TV/DVD
combo to eliminate the interference.
Problem Solution
“No signal” error
message is displayed. •Press INPUT and make sure that you have
selected the correct input for the device or
service you are trying to use.
• If you are using a cable or satellite box, use the
remote that came with that box to change
channels.
• Make sure that you have the correct input
selected to view channels from the cable or
satellite box.
After Auto Channel
Search, there are no
channels.
• Reception can vary by channel depending on the
broadcast power level of a given station. Contact
your cable or satellite TV provider.
• Make sure the antenna or cable/satellite TV is
connected securely to your TV/DVD combo.
• Try replacing the cable between the
antenna/cable or cable/satellite box and your
TV/DVD combo.
One or more channels
do not display. • Make sure that the channels are not blocked. See
“Setting parental control levels” on page31.
• Make sure that the channels are not hidden. The
channel may have been deleted from the
channel list. You can tune to the channel by
pressing the number buttons or you can add the
channel back to the channel list. See “Hiding
channels” on page28.
• If you are using a cable or satellite box, use the
remote that came with that box to change
channels.
• Make sure that you have the correct input
selected to view channels from the cable or
satellite box.
• If you are using an antenna, the digital channel
signal may be low. To check the digital channel
signal strength, see “Checking the digital signal
strength” on page29.
Password is los t. •Enter 9999 to access parental controls, then set
a new password. See “Setting or changing the
password” on page29.
Some settings cannot be
accessed. • If a setting is grayed, the setting is not available
in the current video input mode.
TV/DVD combo cabinet
creaks. • When the TV/DVD combo is in use, the
temperature rises naturally and may cause the
cabinet to expand or contract which can cause a
creaking noise. This is not a malfunction.
Control buttons do not
work. • Make sure that the Button Lock option is set to
Off. See “Locking control buttons” on page30.
• Unplug the power cord, wait a few seconds, then
plug the cord back in and turn on your TV/DVD
combo.
TV keeps turning off. • Make sure that the sleep timer is not turned on.
See “Setting the sleep timer” on page36.
Problem Solution
NS-19LD120A13_11-1329_MAN_V1_ENG.book Page 44 Friday, April 20, 2012 3:10 PM