Insignia NS-27LCD manual 17

Insignia NS-27LCD 27” LCD TV

4 Press and hold the SET button on the remote			Programming the volume lock
	control until the LED blinks twice, then		The remote control comes preset to let you
	release the button.
			control the volume of each connected device.
5 Enter the first five-digit code for your device.
			You can change the volume lock so that one
	The LED blinks once as each digit is entered.		device’s volume controls volume in all modes.
	If the code is correct, the LED blinks twice.		After you lock the volume control, you can unlock
			the volume control for a specific device so you
	Note		can control the volume for that device
		If the LED does not blink twice, repeat steps 3	independently.
		through 5 using a different code.
			To lock the volume control:
6 Aim the remote at the device, then press the
		button.The device should turn off.	1 Press and hold the SET button until the LED
			blinks twice, then release the button.

Note

If the device does not turn off, repeat steps 4 through 6 using a different code. If you cannot find a code that works, see “Searching for a code” on page 17.

7Repeat steps 1 through 6 to program additional devices.

8Press the SET button to save the code and exit.

Searching for a code

To search for a code:

1Press a device key.

2Press and hold the SET button until the LED blinks twice, the release the button.

3Enter 991, then the device group number (0=cable, 1=TV, 2=VCR, 3=audio). The LED blinks twice.

4Aim the remote control at the device, then

press the button. If the device responds, go to step 7.

5If the device does not respond, press the CH+ button. Your remote control will try the next code. Keep pressing the CH+ button until the device responds. You can press the CH– button to try a previous code.

6To search for a code for another device, repeat steps 1 through 5.

7Press the SET button to save the code and exit.

Checking the code

If you programmed a device by searching for a code, you may want to know what four-digit code the remote is using.

To check the code:

1Press the device button on the remote control.

2Press and hold the SET button until the LED blinks twice, then release the button.

3Enter 990. The LED blinks twice.

4Press 1 and count the LED blinks. This is the first digit of the code. For example, if the LED blinks twice, the first digit is 2. If the LED does not blink, the first digit is 0.

5Repeat step 4 using 2 for the second digit, 3 for the third digit, 4 for the fourth digit, and 5 for the fifth digit.

6Press the SET button to exit.

2Enter 993, then press the device button for the device you want to control the volume. The LED blinks twice. When you press the VOL+, VOL–, or MUTE button on the remote control, the device you selected controls the volume regardless of which device you are using.

To unlock the volume control:

1Press and hold the SET button until the LED blinks twice, then release the button.

2Enter 993, then press VOL+ button. The LED blinks four times. The volume control is unlocked.

To unlock a single device’s volume control:

1Press the device key.

2Press and hold the SET button until the LED blinks twice, then release the button.

3Enter 993, then press VOL– button. The LED blinks four times. The volume control for the device you selected is unlocked.

Troubleshooting the remote control

Symptom	Possible solution
LED does not blink when	Replace the batteries.
a button is pressed
LED blinks when a	Make sure that you are at less than 15
button is pressed, but	feet (4.6 meters) from the device and
device does not respond	that you point the remote control at the
	remote sensor on the device.
LED blinks one long	You pressed an incorrect button. Start
blink	the procedure over again.
Remote control does not	Make sure that the device has a remote
control a device or only	sensor, then try another code.
controls some features
of the device
No volume on a device	See “Programming the volume lock”
	on page 17.

www.insignia-products.com 17