Integra RDC-7.1 instruction manual Make a connection for digital audio signal

Connecting to universal DVD player with Multichannel terminal (When an optional Multichannel terminal board is installed on the RDC-7.1)

1.Make a connection for digital audio signal.

If your DVD player has optical output terminal:

Use an optical cable to connect the RDC-7.1’s DIGITAL IN OPTICAL 1 to the optical output on your DVD player. Initially, the OPTICAL 1 digital input is assigned to the DVD input source.

If your DVD player has only coaxial output terminal:

Use a coaxial cable to connect the RDC-7.1’s DIGITAL IN COAXIAL 1-6 to the coaxial output on your DVD player. And you’ll need to reassign the DVD input source after completion of the connection followed by power-on.

1.Press the [Input] button, and then roll the scroll wheel to select “DVD.”

2.Press the scroll wheel, and then press the [Setup] button.

3. Use the [	]/[	] buttons to select “Input Setup,” and then press the [Enter] button.
4. Use the [	]/[	] buttons to select “Audio Assign” and then press the [Enter] button.
5. Use the [	]/[	] buttons to select “Digital Audio,” and then use the [ ]/[ ] buttons to select appropriate ter-

minal (Coax 1-Coax 6).

6. After setting, press the [Setup] button.

2.Use three or four audio connection cables or a multichannel connection cable to connect the multichannel output jack on your DVD player to the MULTI-CH IN 1 jack on the RDC-7.1.

3.If your DVD player has 2-channel analog audio output terminals, in addition to those for multichannel output, use an audio connection cable to connect the RDC-7.1’s AUDIO IN 4 L/R to the terminals on your DVD player.

4.Make a connection for video input (Refer to step 3 on page 5).

DVD player

		AUDIO OUT				VIDEO OUT
AUDIO OUT		MULTICH OUT		AUDIO OUT	S VIDEO	VIDEO	COMPONENT
	FRONT	SURR	CENTER SURR BACK	ANALOG
DIGITAL					OUT	OUT		OUT (RCA)
	L			L			Y	PB	PR
OPTICAL	R			R
			SUB
			WOOFER

1

2

2

2

2

2 3

4

4 4

AB

“Net -Tune”

is a trademark of Onkyo Corporation.

CDIGITAL IN OPTICAL

1

2

3

DDIGITAL IN COAXIAL

1

2

3

E	MULTI	F	AUDIO IN	G
	- CH
FR	FL IN 1	R	L	R
		PH		4
SUB	C
				5
			GND
SR	SL	R	L
		1		6
SBR	SBL

L

H S VIDEO VIDEO

IN IN

1

2

3

I

IN 1

OUT 1

COMPONENT	J		K	L
VIDEO
IN 2	COMPONENT VIDEO			ANTENNA
	((HDHD/BNC/BNC))	IN
Y		Y
PB
		PB
PR				FM
IN 3				75

HDMI		12 V	RS232
		TRIGGER
		OUT
	IN 1	E
			IR IN

+12V DC PWR SUPPLY

20mA MAX.

ETHERNET

(Net-Tune)

4

5

6

4

5

6

	2	7
FR	FL
	3	8
SUB	C
	1	9
SR	SL

4

5

6

PR

Y

OUT

PB Y

PR

PB

AM

GND

IN 2

MAIN

ZONE 2

ZONE 3

12V TRIGGER OUT

A

200mA MAX.

B

RDC-7.1

Option

Option

5.When the connection is completed, power on the RDC-7.1 and TV (See steps 1 to 5 on page 7).

6.Assign the DVD input source. (Remote controller)

1.Press the [Input] button, and then roll the scroll wheel to select “DVD.”

2.Press the scroll wheel, and then press the [Setup] button.

3. Use the [	]/[	] buttons to select “Input Setup,” and then press the [Enter] button.
4. Use the [	]/[	] buttons to select “Audio Assign” and then press the [Enter] button.
5. Use the [	]/[	] buttons to select “Multichannel” and then use the [ ]/[ ] buttons to select “1.”

6. After setting, press the [Setup] button.

7.If you listen to an SACD or DVD-Audio disc, select “Multich” by pressing the [Audio SEL] button on the

6 remote controller.