Intel cpci borard with a intel pentuim M manual Memory Configuration, Configuration Avg Peak, Tbd

Models: cpb4612 cpci borard with a intel pentuim M

1 104
Download 104 pages 57.62 Kb
Page 23
Image 23

Configuration

5V

5V

3.3V

3.3V

 

(avg)

(peak)

(avg)

(peak)

 

 

 

 

 

1.7GHz / 512MB

6.9A

TBD*

2.4A

TBD*

 

 

 

 

 

Hard disk (add)

540mA

1.00A

N/A

N/A

(typical)

 

 

 

 

 

 

 

 

 

PMC card typical1

1.00A

1.70A

0.75A

1.30A

(add)

 

 

 

 

 

 

 

 

 

PMC card max.2

1.50A

3.00A

2.25A

4.50A

(add)

 

 

 

 

 

 

 

 

 

12V

12V

-12V

-12V

(avg)

(peak)

(avg)

(peak)

 

 

 

 

20mA

50mA

0.0A

0.0A

 

 

 

 

N/A

N/A

N/A

N/A

 

 

 

 

100mA

200mA

20mA

40mA

 

 

 

 

500mA

500mA

500mA

500mA

 

 

 

 

*Peak (short duration) power supply current may be significantly higher (up to 50%) and will vary depending upon the application.

Notes:

1.Consult manufacturer of installed PMC card for actual values.

2.In no case shall the total power dissipated by the PMC card exceed 10.0 W.

The cPB-4612 comes with a heatsink that allows the processor to operate between 0° and approximately 50°C ambient with a minimum of 200 LFM (1 meter per second) of external airflow. It is the users' responsibility to ensure that the cPB-4612 is installed in a chassis capable of supplying adequate airflow. The maximum power dissipation of the processor (FCBGA package) is 25W. External airflow must be provided at all times. See Appendix A, "Specifications," and Appendix C, "Thermal Considerations," for more details.

It is strongly recommended that the airflow be measured while the cPB-4612 is installed in its intended location. Insert a thermistor type air velocity meter (Kane-May KM4007 or similar) through the PMC access on the faceplate and make the air velocity measurement near the processor heat sink. Power should not be applied to the cPB-4612 during airflow measurements (slightly disengage the cPB-4612 from the backplane connectors if necessary).

CAUTION: The processor "core" temperature must never exceed 100°C under any condition of ambient temperature or usage. This may result in permanent damage to the processor.

The cPB-4612 may contain materials that require regulation upon disposal. Please dispose of this product in accordance with local rules and regulations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance at http://www.eiae.org/**.

2.3Memory Configuration

The cPB-4612 components can address up to 4 GB of memory, but the board only has two SO-DIMM sockets and can physically only hold two sticks of memory. The address space is divided between memory local to the board and memory located on the Local PCI bus. Any memory not reserved or occupied by a local memory device (DRAM/flash) is available to PCI memory devices.

The cPB-4612 can support up to two sticks of either 256 MB, 512 MB, 1 GB DDR SDRAM. 1MB of L2 cache is integrated with the Pentium® –M processor.

13

Page 23
Image 23
Intel cpci borard with a intel pentuim M, cpb4612 manual Memory Configuration, Configuration Avg Peak, Tbd, 12V Avg Peak