List of Jumpers | Intel EMB-945T instruction

2.4 List of Jumpers

Mini ITX	E M B - 9 4 5 T

2.4 List of Jumpers

The board has a number of jumpers that allow you to configure your system to suit your application.

The table below shows the function of each of the board's jumpers:

Jumpers

Label	Function
JP1	LVDS(1)-LCD(CN12) Voltage Selection
JP2	LVDS(2)-LCD(CN10) Voltage Selection
JP3	COM2 Ring/+5V/+12V Selection
JP4	LCD INVERTER Voltage Selection
JP5	Audio Out Selection
JP6	Clear CMOS

Chapter 2 Quick Installation Guide 2 - 7

Image 21

Intel EMB-945T manual List of Jumpers

Contents

Intel Core Duo/Solo Processor Up to 2.0 GHz EMB-945TMini-ITX Marvell 88E8053 Ethernet AC 97 Audio & Mini PCI Mini-ITX Copyright Notice Acknowledgments Packing List Contents Chapter 2 Quick Installation GuideChapter 1 General Information Chapter 3 Award BIOS Setup Appendix B Programming The Watchdog Timer Driver InstallationChapter Appendix A General Information ChapterChapter 1 General Information 1.1 Introduction Chapter 1 General Information 1.2Features System 1.3 Specifications Display Page Quick Installation Guide Chapter 2 Quick Installation GuideMini ITX 2.1 Safety Precautions Locating Connectors and Jumpers Component Side 2.2 Location of Connectors and Jumpers Locating Connectors and Jumpers Solder Side 2.3Mechanical Drawing Component Side Solder Side 2.4 List of Jumpers Jumpers 2.5 List of Connectors Connectors CN24 2.6 Setting Jumpers OpenClosed 2.8 LVDS2-LCDCN10Voltage Selection JP2 2.7 LVDS1-LCDCN12Voltage Selection JP12.9 COM2 Ring/+5V/+12V Selection JP3 2.10 LCD INVERTER Voltage Selection JP4 2.14 Digital I/O Connector CN2 2.13 CD-INConnector CN12.12 Clear CMOS JP6 Function 2.16 Internal Keyboard Connector CN4 2.15 TV Out Connector CN38 in 8 out 2.18 Audio 5.1 Channel / SPDIF Connector CN6 2.17 Fan2 Connector CN52.19 Internal Mouse Connector CN7 2.20 LCD Inverter Connector CN8 2.21 PCI Express Slot For AAEON CN9 2.23 DVI Connector CN11 2.22 LVDS2-LCDConnector CN10 2.24 LVDS1-LCDConnector CN12 2.26 COM3 RS-232Serial Port Connector CN14 2.25 COM6 RS-232Serial Port Connector CN132.27 Fan1 ConnectorCN15 Pin Signal 2.28 COM5 RS-232Serial Port Connector CN16 2.29 COM4 RS-232Serial Port Connector CN172.30 IrDA Connector CN18 2.32 USB Connector CN20 2.31 ATX Power Connector CN192.33 USB ConnectorCN21 Mini ITXE M B - 9 4 5 T 2.34 EIDE Connector CN22 2.36 COM2 RS-232Serial Port Connector 2.35 Front Panel Connector CN23 Chapter 3 Award BIOS Setup Award BIOS Setup 3.1System Test and Initialization System configuration verification Standard CMOS Features Entering SetupAdvanced BIOS Features 3.2Award BIOS Setup Power Management Setup Advanced Chipset FeaturesPnP/PCI Configurations Load Fail-SafeDefaults Set Supervisor/User Password Save and Exit SetupExit Without Saving Chapter 4 Driver Installation Driver Installation Follow the sequence below to install the drivers SetupYukonWin.exe 4.1 Installation Step 4 - Install Realtek AC97 codec Driver I/O Information AppendixAppendix A I/O Information A-1 Appendix A I/O Information A-2 A.1 I/O Address Map Appendix A I/O Information A-3 A.2 Memory Address Map A.3 IRQ Mapping Chart Appendix A I/O Information A-4 A.4 DMA Channel Assignments Appendix B Programming the Watchdog Time B-1 Programming the Watchdog Timer Configuring Sequence Description B.1 ProgrammingAppendix B Programming the Watchdog Time B-2 2 Modify the Data of the Registers 1 Enter the MB PnP Mode3 Exit the MB PnP Mode Appendix B Programming the Watchdog Timer B-3 WatchDog Timer Configuration Registers Configure Control Index=02hAppendix B Programming the Watchdog Time B-4 Appendix B Programming the Watchdog Timer B-5 B.2 IT8712 Watchdog Timer Initial Program game port enable mov cl, call Set Logic Device CALL Read Configuration Data CMP AL,87h RET Exit Configuration Mode ENDPCALL Read Configuration Data CMP AL,12h Read Configuration Data PROC NEAR MOV DX,WORD PTR CS Cfg Port+06h IN AL,DX RET push ax push cx xchg al,cl mov cl,07h END Maincall Superio Set Reg pop cx pop ax ret Set Logic Device endp