Intel PCA-6175 - page 19

Chapter 1 Hardware Configuration

1.6 Board Layout: Jumper Locations

Figure 1-1: Board layout: jumper locations

Contents

Main Copyright Notice Acknowledgements A Message to the Customer Advantech Customer Services Technical Support Product Warranty Initial inspection Contents Chapter 1 Hardware Configuration ....... 1 Chapter 2 Connecting Peripherals ..... 23 Chapter 3 Award BIOS Setup .............. 31 Page Page Hardware Configuration CHAPTER 1.1 Introduction 1.2 Features 1.3 Specifications System Memory Input/Output Industrial features Mechanical and environmental specifications 1.4 Board Layout: Main Features 1.5 Jumpers and Connectors Page Page Page 1.8 Safety Precautions 1.9 Jumper Settings 1.9.1 How to set jumpers 1.9.2 CPU core frequency (J5) 1.9.3 CMOS clear (J6) 1.9.4 Watchdog timer output (J8) 1.9.5 CPU bus clock select (J11) Note: 75 MHz exceeds the product's specifications. 1.9.6 DiskOnChip 2000 Flash disk address select (J12) 1.10 System Memory Page 1.11 Memory Installation Procedures 1.12 Cache Memory 1.13 Mounting the CPU and Cooling Modules Step 1 Page Page Connecting Peripherals CHAPTER 2.1 Primary (CN6) and Secondary (CN7) IDE Connectors 2.2 Floppy Drive Connector (CN13) 2.3 Parallel Port Connector (CN8) 2.4 Keyboard & PS/2 Mouse Connector (CN12) 2.5 Serial Ports (CN9: COM1; CN10: COM2) 2.6 Front Panel Connectors (CN2, CN3, CN4, J1 and J2) 2.6.1 Keyboard lock and power on LED (CN2) 2.6.2 External speaker (CN3) 2.6.3 IDE LED (CN4) 2.6.4 ATX soft power switch (J1) 2.7 ATX Power Control Connectors (J7 and J1) 2.7.1 ATX feature connector (J7) and soft power switch connector (J1) 2.7.2 Controlling the soft power switch 2.8 USB Connector (CN11) 2.9 IR Connector (CN1) 2.10 External Keyboard Connector (J10) 2.11 External Suspend Switch Lead (SMI) (J3) Page Page 3.4 BIOS Features Setup 3.4.1 Virus Warning 3.4.2 Quick Power On Self Test 3.4.3 Boot Sequence 3.4.4 Boot Up Floppy Seek Page Page 3.5 CHIPSET Features Setup 3.6 Power Management Setup 3.6.1 Power Management 3.6.2 HDD Power Management Note: The HDD will not power down if the Power Management option is disabled. 3.7 PCI Configuration Setup Page 3.9 Password Setting 3.10 IDE HDD Auto Detection Page A Programming the Watchdog Timer Page Page Pin Assignments APPENDIX B B.1 COM1/COM2 RS-232 Serial Port (CN9,CN10) B.2 Keyboard and Mouse Connnector (CN12) B.3 External Keyboard Connector (J10) B.4 ATX Feature Connector (J7) B.5 IDE Hard Drive Connector (CN6, CN7) * Low active 39 37 .... 3 1 40 38 .... 4 2 B.6 USB Connector (CN11) B.7 CPU Fan Power Connector (CN5) B.8 Floppy Drive Connector (CN13) * Low active 33 31 .... 3 1 34 32 .... 4 2 B.9 Parallel Port Connector (CN8) 13 12 .... 2 1 26 25 .... 15 14 B.10 IR Connector (CN1) B.11 HDD LED Connector (CN4) B.12 Power LED and Keylock Connector (CN2) B.13 External Speaker (CN3) B.14 System I/O Ports B.15 DMA Channel Assignments B.16 Interrupt Assignments B.17 1st MB Memory Map Page C C.1 DiskOnChip 2000 Quick Installation Guide C.1.1 DiskOnChip 2000 installation instructions C.1.2 Additional information and assistance