INSTALLATION
1Mark frame hole locations.
A. Open hinge and place frame | 1/8” |
leaf flat against surface of |
|
frame leaving 1/8” gap |
|
between top of hinge |
|
and frame header. |
|
Hinge lip should be |
|
held tight against the |
|
frame face from top |
|
to bottom. |
|
B. Mark all hole locations
on frame using center punch provided.
C.Drill all holes using #13 (.185”)
or 3/16” (.188”) drill for metal frame.
For wood frame use 5/32” (.156”) drill. Optional wood screw pack required.
D.DO NOT install hinge to frame at this time.
2Mount hinge to door.
3Mount door to frame
A.With door held securely, position door 90 degrees to opening and align mounting
holes in frame leaf of hinge | Frame |
with marks on frame made | |
in step 1. Note: An angle | Door |
block, jack or shims will be |
|
helpful in positioning the |
|
door properly. |
|
B.With hinge and door held securely and accurately in place, install
4 Check for proper operation |
and clearances. |
A.Place door leaf of hinge against hinge edge of door so that top of hinge is flush with top of door. Hinge aligment lip must lay flat against full length of door.
Door
Top view
Flush
Door
A. Close door and check for |
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| ||||
proper operation. |
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
| 1/8” |
|
|
|
| |||
B. Check push side of door for |
|
|
|
|
|
|
|
|
|
|
| |||
proper clearances. Clearance |
|
|
|
|
| 5/16” |
|
|
|
| ||||
|
|
|
|
| ||||||||||
for single door is shown to the |
|
|
|
|
|
|
|
|
|
|
| |||
right and double door is |
|
|
|
|
|
|
|
|
|
|
| |||
shown below. |
|
|
|
| 1/8” |
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| |||||
C. Check with NFPA 80 manual |
|
|
|
|
|
|
|
|
|
|
| |||
for clearance requirements |
|
|
|
|
|
|
|
|
|
|
| |||
on |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
B.With hinge held firmly in place, mark all hole locations on frame using center punch.
C.Drill all holes as in step 1.
D.Attach hinge leaf to door using fasteners provided and #3 phillips drive. See screw chart below.
Note: Fasten top screw first, and bottom most screw second, making sure hinge is aligned correctly.
Screw Chart
Door & Frame | Screw Type | |
Material | ||
| ||
|
| |
Metal frame & | ||
metal door | ||
| ||
Metal frame & | ||
wood door* | #12 x | |
|
| |
Wood frame* & | #12 x | |
wood door* | ||
| ||
|
|
*Optional wood screw pack required.
1/8” | 1/8” |
5/16” | 5/16” |
3/16” |
|
Page 2 of 2 |