JAI operation manual CV-A1 RS-232C command list, Timing and shutter related commands

CV-A1

7.2. CV-A1 RS-232C command list.

			Command Name		Format		Parameter		Remarks
		A	–	General settings and	useful commands
EB			Echo Back		EB=[Param.]<CR><LF>		0=Echo off	1=Echo on	Off at power up
ST			Camera Status request		ST?<CR><LF>				Actual setting
HP			Online Help request		HP?<CR><LF>				Command list
VN			Firmware version		VN?<CR><LF>				3 letter version
ID			Camera ID request		ID?<CR><LF>				10 characters *3)
MD			Model name request		MD?<CR><LF>				≤10 characters *3)
UD			User ID		UD= Param. <CR><LF>		Save and load user text
					[	]			≤16 characters *3)
	B – Timing and shutter related commands
SC			Scanning format		SC=[Param.]<CR><LF>		0=full frame	1=1/2 partial
							2=1/3 partial	3=1/6 partial
TR			Trigger mode		TR=[Param.]<CR><LF>		0=normal	1=Edge
							2=Pulse width	3=Frame delay
							4=Long time	5=Start/stop
							6=Smearless
SM			Shutter mode		SM=[Param.]<CR><LF>		0=Normal	1=Programmab.
SH			Shutter speed		SH=[Param.]<CR><LF>		0=Off	1=1/30	All16 step is valid
							2=1/60	3=1/100	in normal trigger
							4=1/250	5=1/500	mode.
							6=1/1000	7=1/2000	In all trigger
							8=1/4000	9=1/8000	modes shutter
							10=1/20,000	11=1/40,000	speeds higher
							12=1/80,000	13=1/120,000	than 9 will result
									in 1/12,000
							14=1/160,000	15=1/200,000
PE			Programmable expos.		PE= Param. <CR><LF>		0=1.3 H, 1=1.3H	1023=1023.3 H
					[	]			H= 58.4∝sec
BI			Binning		BI=[Param.]<CR><LF>		0=off	1=vertical	*1)
							2=horizontal	3=hor. + ver.
HC			HD accumulation		HC=[Param.]<CR><LF>		0=H synchron	1=a-synchron	a-sync. only for
							accumulation	accumulation	TR=1 and TR=3
	C – Signals and polarity
SO			Sync signal		SO=[Param.]<CR><LF>		0=no sync	1=sync on video
PC			Pixel clock		PC=[Param.]<CR><LF>		0=no clock out	1=clock out	Should be off
									when not used
EW			EEN/WEN		EW=[Param.]<CR><LF>		0= EEN out	1=WEN out	Pin#6 on 6 pin
TP			Trigger polarity		TP=[Param.]<CR><LF>		0= active low	1= active high	*2)
WP			WEN polarity		WP=[Param.]<CR><LF>		0= active low	1= active high
	D – Gain and analogue signals setting
AS			AGC Switch		AS=[Param.]<CR><LF>		0=AGC off	1=AGC on	0= manual gain
AG			AGC Level		AG=[Param.]<CR><LF>		0=low	255=high	Range 0 to 255
GA			Manual gain Level		GA=[Param.]<CR><LF>		0=low	255=high	Range 0 to 255
RP			Rear Potentiometer		RP=[Param.]<CR><LF>		0=manual gain	1=rear potm.
SU			Setup Level		SU=[Param.]<CR><LF>		0=low	255=high	Range 0 to 255
WC			White clip Level		WC=[Param.]<CR><LF>		0=low	255=high	Range 0 to 255
GS			Gamma Select		GS=[Param.]<CR><LF>		0=gamma 1	1=gamma 0.45
	E – Saving and loading data in EEPROM
LD			Load settings from		LD=[Param.]<CR><LF>		0=Factory data	1=User 1 area	Latest used data
			camera EEPROM				2=User 2 area	3=User 3 area	area becomes
									default at next
									power up
SA			Save settings to		SA=[Param.]<CR><LF>		1=User 1 area	2=User 2 area
			camera EEPROM				3=User 3 area
EA			EEPROM area request		EA?<CR><LF>				Return latest used
									area

*1) The internal pixel clock is not changed in H binning (BI=2 and BI=3). To keep the aspect ratio correct, divided the clock by 2 in the frame grabber.

*2) If positive logic is used (TP=1), the first trigger pulse after power up will be ignored.

*3) Functions implemented from s/no E102910

- 18 -