OPERATION3.0AND
CONTROLS
ATTENTION: VOIR LE CAHIER D' | S800 POWER AMPLIFIER |
|
| JBL SYNTHESIS | DESIGNED, ENGINEERED AND MANUFACTURED | TRIGGERS | IN |
INSTRUCTION |
|
|
| NORTHRIDGE, CA | IN THE UNITED STATES OF AMERICA |
|
|
| Ch. 1 | BRIDGED | Ch. 2 |
|
|
| |
WARNING; To reduce the risk of fire or |
|
|
|
|
| ||
BRIDGED |
|
| Input |
|
|
| |
electric shock, do not expose | MONO | STEREO |
|
|
| ||
this appliance to rain or moisture | Input |
|
|
|
| ||
|
|
|
|
|
| ||
No user serviceable parts inside. Refer |
|
|
|
|
| OUT | |
|
|
|
|
|
| ||
servicing to qualified personnel. |
|
|
|
| MANUAL | AUTO | |
|
|
|
|
|
| ON | ON |
CAUTION |
|
|
|
|
|
|
|
RISK OF ELECTRIC SHOCK |
|
|
|
|
|
|
|
DO NOT OPEN |
|
|
|
|
|
|
|
AVIS: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR |
|
|
|
| ON |
| |
|
|
|
|
|
|
| |
|
|
|
|
|
| 10A |
|
|
|
|
|
|
| 120V ~ |
|
|
|
|
|
|
| 50/60Hz |
|
|
|
|
|
|
| 1200W |
|
WARNING: HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING. | +BRIDGED - |
|
| OFF |
| ||
|
|
|
| ||||
| - | + | + | - |
|
|
|
serial number | Ch. 1 Output | Ch. 2 Output |
| 20A 120VAC/60Hz 2400 W | |||
|
|
|
|
|
|
S800S
black terminals. Wire the "+" terminal of the speaker to the left red terminal, and the
In bridged mode, speakers connect only to the "hot" (red) amplifier output connectors, and neither can be connected to ground under any circumstances, as damage to the S800 will result.
NOTE: The minimum load impedance that this amplifier can handle safely is two ohms per channel in stereo operation, and four ohms in mono. Using lower impedance loads can damage the unit and will void your warranty!
Use the following chart as a guide to the appropriate gage of wire to use for different
Wire Run Length | Rec. Ga. |
Wire Run Length | Minimum Gage |
Up to 20' | 16 |
|
|
Up to 50' | 14 |
|
|
Up to 100' | 12 |
7. Circuit Breaker/Main Power Switch
The main power switch, located on the rear panel of the S800, is also a circuit breaker. Putting this switch in
the ON position allows the amplifier to enter the "standby" and "operate" modes as controlled by the front panel POWER switch and Manual On/Auto On switches. Should the amplifier be asked to produce more power than its design allows for a prolonged period, or should the S800 draw an amount of current from the AC power source that could damage internal components, the handle of this switch will move to a center position. Reduce the audio level and wait a minute for the circuit breaker to reset, then move it to the OFF, then the ON position. If the handle returns to the center ("tripped") position, service is required; contact your JBL Synthesis dealer.
The S800 was designed to operate reliably under virtu- ally all conditions. Even momentary short circuiting of the output (speaker) connections will not ordinarily damage the output circuitry (although this will activate internal protective circuitry and cause one or more of the
There are no
11