JBL Complete Specifications for SR-X Series Stereo Systems

SPECIFICATIONS

Model

LF

Mid

HF

Horn

Rated

System

Freq Range

Crossover

Nominal

Dispersion

Weight

Shape

Dimensions

Driver

Driver

Power*

Impedance

(-10 dB)

Frequency

Sensitivity**

(H X V)

SR4702X

2206H

--

2426H

OASR

600

8

42Hz-20kHz

1.3 kHz

95dB

85º x 85º

29 kg

Multi-angle

648 x 403 x 356

64 lbs

Monitor

25.5 x 15.9 x 14

SR4715X

2226H

--

--

--

1200

4

35Hz-300Hz

80 - 100 Hz

100dB

--

47.2 kg

Rectangular

1067 x 616 x 435

(x2)

recommended

104 lbs

42 x 24.3 x 17.1

SR4718X

2241G

--

--

--

600

4

38Hz-300Hz

80 – 100 Hz

98dB

--

39.9 kg

Rectangular

616 x 613 x 610 mm

recommended

88 lbs

24.3 x 24.1 x 24 in

SR4719X

2241H

--

--

--

1200

4

30Hz-300Hz

80 – 100 Hz

101dB

--

85.3 kg

Rectangular

765 x 1219 x 616

(x2)

recommended

188 lbs

30.1 x 48 x 24.3

SR4722X

2206H

--

2417H

OASR

600

8

42Hz-18kHz

1.2 kHz

95dB

85º x 85º

27.2 kg

Trapezoidal

686 x 486 x 333

SR4722X/F

60 lbs

27 x 19.1 x 13.1

SR4725X

2226H

--

2426H

2370A

600

8

35Hz-18kHz

1.1 kHz

98dB

90º X 40º

37.2 kg

Trapezoidal

718 x 616 x 435

SR4725X/F

82 lbs

28.3 x 24.3 x 17.1

SR4726X

2226H

--

2447H

2381

600

8

35Hz-20kHz

1.1 kHz

97dB

90º X 50º

48.5 kg

Trapezoidal

883 x 616 x 435

SR4726X/F

2383

60º X 50º

107 lbs

34.8 x 24.3 x 17.1

SR4731X

2206H

--

2447H

2381

1200

4

39Hz-20kHz

1.2 kHz

98dB

90º X 50º

59.9 kg

Trapezoidal

1067 x 616 x 435

SR4731X/F

(x2)

2383

60º X 50º

132 lbs

42 x 24.3 x 17.1

SR4732X

2206H

2447H

2404H

2381

1200

4

39Hz-21kHz

1.2 kHz,

98dB

90º X 50º

62.1 kg

Trapezoidal

1067 x 616 x 435

SR4732X/F

(x2)

6 kHz

137 lbs

42 x 24.3 x 17.1

SR4733X

2226H

--

2447H

2381

1200

4

37Hz-20kHz

1.2 kHz

100dB

90º X 50º

65.8 kg

Trapezoidal

1219 x 616 x 435

SR4733X/F

(x2)

2383

60º X 50º

145 lbs

48 x 24.3 x 17.1

SR4735X

2226H

M209-8A

2426H

MH1

600

8

36Hz-20kHz

340 Hz and

97dB

70º X 50º

50.8 kg

Trapezoidal

946 x 616 x 479

SR4735X/F

1.6 kHz

112 lbs

37.3 x 24.3 x 18.9

* IEC filtered random noise with a 6 dB crest factor

**1W@1m (2.83V for 8ohms, 2.00V for 4ohms, ave'd 500Hz-5kHz) Specifications subject to change without notice

DuraFlex

The SR-X loudspeaker system is finished in JBL's DuraFlex™. DuraFlex is tough and inherently flexible and it is extremely resistant to knocks, scratches and scuffs. The DuraFlex finish on your SR-X speakers is actually much tougher than the plywood to which it is applied. Note: SR-X enclosures are not paintable. In the event that cosmetic damage occurs to your speakers, a DuraFlex touch-up kit (PN 16677) is available from JBL.

Recommended Power

The following table shows the recommended amplifier power for SR-X models.

Model	Full-Range / Parallel (1)	HF (2)	LF (3) / Discrete (4)
SR4702X	600 to 1,200W@8Ω	100 to 200W@8Ω	600 to 1,200W@8Ω
SR4715X	1,200 to 2,400W@4Ω	n/a	600 to 1,200W@8Ω x2
SR4718X	600 to 1,200W@4Ω	n/a	n/a
SR4719X	1,200 to 2,400W@4Ω	n/a	600 to 1,200W@8Ω x2
SR4722X	600 to 1,200W@8Ω	60 to 120W@8Ω	600 to 1,200W@8Ω
SR4725X	600 to 1,200W@8Ω	100 to 200W@8Ω	600 to 1,200W@8Ω
SR4726X	600 to 1,200W@8Ω	150 to 300W@16Ω	600 to 1,200W@8Ω
SR4731X	1,200 to 2,400W@4Ω	150 to 300W@16Ω	1,200 to 2,400W@4Ω
SR4732X	1,200 to 2,400W@4Ω	150 to 300W@16Ω	1,200 to 2,400W@4Ω
SR4733X	1,200 to 2,400W@4Ω	150 to 300W@16Ω	1,200 to 2,400W@4Ω
SR4735X	600 to 1,200W@8Ω	100 to 200W@8Ω	600 to 1,200W@8Ω

1.Full-range / Parallel: Is the amplifier power required to optimally drive this speaker system when used in full- range (passive) mode. In the case of dual-driver subwoofer models, this is the power required to drive both transducers at the same time.

2.HF: Is the amplifier power required to optimally drive the high-frequency section of this speaker system when used in bi-amp mode.

3.LF: Is the amplifier power required to optimally drive the low-frequency section of this speaker system when used in bi-amp mode.

4.Discrete: Is the amplifier power required to optimally drive an individual transducer in a dual transducer subwoofer.

5.±1 or ±2 Pass-Thru: This allows for the convenience of a single conductor cable from the amplifier rack to the

speakers stack, this configuration supplies separate amplifier power to the subwoofer (ie ±2) and to the	7
mid-high speaker (ie 1 Pass-Thru).