JCDWIN

INSTALLATION

 

problem is corrected. Once proper operation is achieved, turn the ignition switch off and

Before You Begin

 

proceed with final mounting of the chassis.

 

 

7. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is

1.

Disconnect Battery

 

fully seated and the spring clips lock it into place.

 

Before you begin, always disconnect the battery negative terminal.

8. Attach one end of the

 

 

2.

Remove Transport Screws

 

perforated support strap

 

Dashboard

Important Notes

 

(supplied) to the screw stud on

 

Support Strap

 

the rear of the chassis using

 

 

 

 

Before final installation, test the wiring connections to make sure the unit is connected

the hex nut and spring washer

Plain Washer

 

properly and the system works.

 

provided. Fasten the other end

Screw (5 x 25mm)

Use only the parts included with the unit to ensure proper installation. The use of

of the perforated strap to a

 

 

 

unauthorized parts can cause malfunctions.

 

secure part of the dashboard

 

Screw Stud

Consult with your nearest dealer if installation requires the drilling of holes or other

either above or below the radio

Hex Nut (5mm)

 

 

 

modifications to your vehicle.

 

using the screw and plain

Spring Washer

Install the unit where it does not interfere with driving and cannot injure passengers if

washer provided. Bend the

 

 

 

there is a sudden or emergency stop.

 

strap, as necessary, to position

 

 

If the installation angle exceeds 30º from horizontal, the unit might not give optimum

it. CAUTION: The rear of the

 

 

 

performance.

 

radio must be supported with

 

 

This unit is not waterproof and is intended for interior mounting applications only.

the strap to prevent damage to

 

 

 

Exterior mounting of the unit requires use of an ASA approved marine housing.

the dashboard from the weight

 

 

Avoid installing the unit where it will be subject to high temperatures from direct sunlight,

of the radio or improper operation due to vibration.

 

hot air, or from a heater, or where it would be subject to excessive dust, dirt or vibration.

9. Test radio operation by referring to the operating instructions for the unit.

Be sure to remove the control panel before installing the unit.

Removing the Unit

 

 

Mounting the Unit

 

 

 

 

To remove the radio after installation, insert the

Removal Key

This unit can be property installed with a conventional DIN front mount.

removal keys straight back until they click, and

 

1.

Slide the mounting sleeve off of the chas-

Dashboard

then pull the radio out. If removal keys are

 

inserted at an angle, they will not lock properly

 

 

sis if it has not already been removed. If it

 

 

 

 

to release the unit.

 

 

 

is locked into position, use the removal

Bend Tabs

 

 

 

 

 

 

 

keys (supplied) to disengage it. The

182

Reconnect the Battery

 

 

 

 

 

 

 

removal keys are depicted in “Removing

53

When wiring is complete, reconnect the battery

 

 

the Unit” on page 3.

 

 

Screw Stud

 

 

negative terminal.

 

 

2.

Check the dashboard opening size by

 

 

 

 

 

 

 

sliding the mounting sleeve into it. If the opening is not large enough, carefully cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening or cause it to bend

or bow. Check that there will be sufficient space behind the dashboard for the radio chassis.

3.Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary to firmly secure the sleeve to the dashboard.

4.Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve.

5.Follow the wiring diagram carefully and make certain all connections are secure and insulated with crimp connectors or electrical tape to ensure proper operation.

6.After completing the wiring connections, turn the unit on to confirm operation (vehicle ignition switch must be on). If the unit does not operate, recheck all wiring until the

3

Page 3
Image 3
Jensen JCDWIN operation manual Jcdwin Installation, Before You Begin, Important Notes, Removing the Unit Mounting the Unit